Bedienungsanleitung Liftmaster 8500 Elite (Seite 24 von 36) (Englisch)

600889

Zoom out

Zoom in

Vorherige Seite

1/36

Nächste Seite

LIGHTS

Press the LIGHT button to turn the garage

door opener lights on or off. When the

lights are turned on they will stay on until

the LIGHT button is pressed again, or

until the garage door opener is activated.

Once the garage door opener is activated

the lights will turn off after the speciﬁ ed

period of time (the factory setting is 4-1/2

minutes). The LIGHT button will not control

the lights when the door is in motion.

To change the amount of time the garage

door opener lights will stay on:

Press and hold the LOCK button until the

garage door opener lights ﬂ ash. The time

interval is indicated by the number of

ﬂ ashes.

NUMBER OF TIMES

GARAGE DOOR OPENER

LIGHTS FLASH

TIME THE

GARAGE DOOR OPENER

LIGHT STAYS ON

1 1 ½ Minutes

2 2 ½ Minutes

3 3 ½ Minutes

4 4 ½ Minutes

Light Feature

The lights will turn on when someone

enters through the open garage door and

the safety reversing sensor infrared beam

is broken.

Activate:

Start with the garage door opener lights

on. Press and hold the LIGHT button

until the garage door opener lights turn

off, then on again.*

Deactivate:

Press and hold the LIGHT button until

the garage door opener lights turn on,

then off again.*

* Approximately 10 seconds

Operation

PUSH BAR

Press the push bar to open/close the door.

LOCK

Designed to prevent operation of the door

from hand-held remote controls. However,

the door will open and close from the

Door Control, the Outdoor Key Switch,

the Keyless Entry Accessories and MyQ

Internet Gateway.

Activate:

Press and hold the LOCK button for 2

seconds. The command LED will ﬂ ash

as long as the lock feature is activated

and your handheld remote control will

not operate your door at this time.

Deactivate:

Press and hold the LOCK button again

for 2 seconds. The command LED will

stop ﬂ ashing and normal operation will

resume.

MOTION SENSOR

This feature will automatically turn on the

garage door opener lights when motion is

sensed. The lights will come on for 4-1/2

minutes, then shut off.

Activate/Deactivate:

Slide the motion sensor switch ON or

OFF.

Using the Door Control (MyQ

Control Panel)

NOTE: Due to power consumption this door control (Model 888LM) cannot be used in conjunction with another wired door control

connected to your garage door opener. If an additional door control is needed, the wireless door control model 885LM can be

programmed to the door control (Model 888LM). To program the 885LM to the MyQ

Control Panel, follow the remote control

programming steps.

NOTE: MyQ

light controls will continue to work however all other MyQ

devices and TTC will not work if using the Model 580LM

Alternate Power Supply or when in Battery Backup mode.

TIMER-TO-CLOSE (TTC)

The TTC feature automatically closes the

door after a speciﬁ ed time period (1, 5,

or 10 minutes). Once the TTC has been

set and the door is open, the LED for the

selected close interval will blink and begin

to count down to close the door. The

control panel will beep and the garage door

opener lights will ﬂ ash before closing the

door.

The TTC feature will deactivate if the garage

door encounters an obstruction twice; or

the safety reversing sensors are incorrectly

installed. The garage door will reverse open

and WILL NOT close until the obstructions

are clear or the safety reversing sensors are

correctly installed. When the obstruction

has been cleared or the safety reversing

sensors have been aligned, the door will

close when the garage door opener is

activated.

Activate:

Press and hold the ON button until

one of the TTC LEDs light up. Then

press the ON button again to cycle

through the time interval options (the

corresponding TTC LED will light

for each time interval). The garage

door opener light bulbs will blink as

conﬁ rmation.

Deactivate:

Press and hold the OFF button until all

TTC LEDs turn off and a beep is heard

from the control panel.

To suspend the TTC:

To suspend the TTC and temporarily

hold the door open, press and release

the HOLD OPEN button (the HOLD

OPEN LED will turn solid). The TTC

will remain suspended until the HOLD

OPEN button is pressed again or the

garage door opener is activated from

another device (door control, remote

control, keyless entry, etc.).

LIGHT Button

HOLD OPEN

Button for the

Timer-To-Close

(TTC)

Motion Sensor

Push Bar

1 Minute

TTC LED

5 Minute

TTC LED

10 Minute

TTC LED

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Liftmaster 8500 Elite Seite 24

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info