600892
20
Zoom out
Zoom in
Vorherige Seite
1/41
Nächste Seite
20
Power
1 Connect Power
To preventpossible SERIOUS INJURY or DEATHfrom electrocution or fire:
l Be sure power is NOT connected to the opener, and disconnectpower to circuitBEFORE
removing cover to establish permanentwiring connection.
l Garage door installation and wiring MUST be in compliance with ALL local electrical and
building codes.
l NEVER use an extension cord, 2-wire adapter,or change plug in ANY way to make itfit
outlet. Be sure the opener is grounded.
To avoid installation difficulties, do not activate
the garage door openerat this time.
To reduce the riskofelectricshock,your garage
door opener has a grounding type plug with a third
grounding pin.Thisplug will only fit into a
grounding type outlet. Ifthe plug doesn’tfit into your
outlet, contacta qualified electrician to install the
proper outlet.
THERE ARE TWO OPTIONS FORCONNECTINGPOWER:
OPTION A
TYPICAL WIRING
1. Plug in the garage door opener into a
grounded outlet.
2. DO NOT run garage door opener at this
time.
TYPICAL WIRING
OPTION B
PERMANENT WIRING
If permanentwiring is required by your local code, refer to the following procedure.To make a
permanent connection through the 7/8 inch hole in the top of the motor unit(according to local code):
Wiring througha filter board (8550 models manufactured
before April12, 2013):
1. Be sure power is NOT connected to the opener,
and disconnectpower to circuit.
2. Remove the garage door opener cover and set
aside.
3. Remove the attached green ground terminal.
4. Cut blackand white wires.Strip away 1/2 inch (1
cm) of insulation, 3 inches (7.5 cm) before spade
terminals.
5. Remove the power cord from opener.
6. Install a conduitor flexcable adapter to the 7/8 inch
hole.
7. Run wires through conduit, cutto proper length and
strip insulation.
8. Attach with wire nuts provided. Attach the ground
wire to the green ground screw.The opener must
be grounded.
9. Properly secure wire under plastic tiesso thatwire
doesnotcome in contact with moving parts.
10. Reinstall the cover. DO NOT run garage door
opener atthistime.
Ground Tab
Green Ground
Screw
Ground Wire
Black
Wire
White Wire
PERMANENT WIRING
Wire Nuts
Wiring througha terminalblock (8550 models
manufactured afterApril12,2013 and all8557 models):
1. Remove the motor unitcover screwsand set the
cover aside.
2. Remove the attached 3-prong cord.
3. Connectthe black (line) wire to the screw on the
brass terminal; the white (neutral) wire to the screw
on the silver terminal; and the ground wire to the
green ground screw.The openermust be
grounded.
4. Reinstall the cover.
Ground Tab
Gr
een
Ground
Screw
Ground
Wire
White Wire
PERMANENT WIRING
Black
Wire
Black
Wire
20

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Liftmaster 8550 Elite wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info