Bedienungsanleitung LightPro LED Strip Connector 176L (Seite 6 von 12) (Deutsch, Englisch, Holländisch, Französisch)

697398

Zoom out

Zoom in

Vorherige Seite

1/12

Nächste Seite

LED Strip and Connector

User manual

Thank you for buying the Lightpro LED Strip and

Connector. This document contains the required

information for correct, efcient, and safe use of the

product. Consult the general manual of the Lightpro

12-volt system and the user manual of your Lightpro

transformer for more information about the set up and

connection of your light plan.

Read the information in this manual carefully before

using the product. Keep this manual near the product

for consultation in the future.

PRODUCT DESCRIPTION

The Lightpro LED Strip is a lighting chain for outdoor

use. The strip can be cut to the desired length before

installation. Attention: before cutting, read the instruc-

tions in this manual carefully!

This product can be used as outdoor lighting in com-

bination with the Lightpro 12 Volt system. Improper

use of the product can have consequences for the

safety, warranty, and correct functioning of the product

and/or other parts of the system.

Specications LED Strip

Article number 175L

Power (per meter) 2,2W

Luminous ux (per meter) 80-100lm

Protection class IP67

Ambient temperature -20°C to 50°C

Dimmable No

Specications LED Strip Connector

Article number 176L

Maximum Power 36W

Afmetingen (l x b x h) 1m x 28mm x 28mm

Protection class IP44

Ambient temperature -20°C to 50°C

Cable length 1m

USE

Packaging content

[Figure A]

1. LED Strip Connector

2. Sealing rubber

3. End cap

Check if all parts are present in the packaging. For

questions about parts, service, and any complaints or

other remarks, you can always contact us.

E-mail: info@lightpro.nl

Available separately

[Figure B]

1. LED Strip (Article number 175L)

2. Lightpro connector (Article number 137A)

CUTTING

[Figure C]

The LED Strip can be cut to any desired length. Cut

through in one movement from the transparent side.

Carefully follow these instructions when cutting the

strip:

1. The LED Strip has been marked with the print DO

NOT CUT HERE. Never cut in this part of the strip.

2. The strip can be shortened as desired. The part of

the strip that is connected to the connector has to

have at least one marking.

3. Short (remaining) parts of the LED Strip which do

not have a marking will not light when connected to

the connector.

4. It is possible that a small part of a few centimetres at

the end of the strip will not light up after cutting.

ASSEMBLE

[Figure D]

1. Unscrew the screw cap and move it to the back.

The LED Strip has to be connected in the right

direction to the connector. When connecting, pay

attention to the direction of the arrow with the print

CONNECTOR. The arrow points in the direction of the

connector.

2. Place the sealing rubber at around 5 cm on the LED

Strip.

3. Connect the LED Strip to the Connector. Make sure

the pins in the connector make proper contact with

the conductors in the strip.

4. Press the sealing rubber to the connector.

5. Place the screw cap on the connector and tighten

properly.

6. Place the end cap at the end of the LED Strip.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

LightPro LED Strip Connector 176L Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info