724635

Lightway FPC-088 Seite 2

2
Zoom out
Zoom in
Vorherige Seite
1/2
Nächste Seite
Charging the LED Light (ALWAYS CHARGE BEFORE USE)
WARNING: Before charging the LED light ensure it is dry and not operational/ turned on during
charging process. NOTE: During the charging process, do not activate the lights until the lights are
fully charged.
WARNING: Only use the cable supplied for charging the LED.
NOTE: Always charge the LED light before rst use
1. Insert the USB end of the charging cable (16) into a USB charging point (laptop, PC, Phone
charger with USB outlet, powerbank etc) (Fig A).
2. Insert the 2 prong end of the charging cable (16) into the charging port (2) on the LED Light
(Fig B). The USB charging light (3) will be “red” to indicate charging. When charged, the USB
charging light (3) will change to “green” (Fig C, and #3 image
above). The charging process takes approximately 3.5 hours.
3. When charged, remove the charging cable from the USB charge
port (2) on the LED (1). Insert the USB Port rubber plug (17) into
the USB charge port (2) (Fig D). This ensures there is no water
ingress when the LED light is placed in water. The LED light is
now ready for use.
Removing the Isolator on the Remote control
IMPORTANT: Before using the remote control the isolator strip must be removed otherwise
remote control will not function.
1. Isolator can be removed by pulling it from the remote control battery compartment (5). (Fig E)
2. If unremovable, you need to open and partially remove battery compartment (5).
3. Using a small screwdriver* loosen the safety screw (15) in an anticlockwise direction and
remove (Fig F). Release battery compartment cover by pushing the safety lever (6) to
right (unlocking compartment), then pull remote control battery compartment (5) out
approximately ½ way to remove isolator. (Fig G/H)
NOTE: Directions showing how to open compartment are shown on remote control (Fig H).
4. When isolator removed, insert battery compartment (5) back into remote control and ensure
safety lever (6) has fully engaged. If not, push safety lever (6) outward to engage (Fig I).
Always check battery compartment (5) cannot be pulled out without disengaging safety
lever (6).
5. Secure battery compartment (5) by re-inserting the screw, and using a small screwdriver*,
tighten compartment screw in clockwise direction.
Changing the battery on the Remote Control
NOTE: The remote control is already tted with a button battery.
IMPORTANT: Ensure the replacement battery is the correct button specication
(CR2025 3 VOLTS) before replacing.
WARNING: KEEP OUT OF REACH OF CHILDREN. Swallowing may lead to serious injury
or death in as little as 2 hours due to chemical burns and potential perforation of the
esophagus. If swallowed, immediately go to a hospital emergency room.
1. Using a small screwdriver* loosen screw in anticlockwise direction and remove. Release
battery compartment cover by pushing safety lever (6) to right, then pull battery
compartment (5) out. (G/H)
2. Remove current button battery
and dispose of.
NOTE: refer to safety instructions
for responsible disposal of the
battery.
3. Insert new button battery into battery compartment (5) ensuring battery is sitting ush and
battery is at side up. (Fig K/L)
4.
Insert battery compartment (5) with new button battery into remote control ensuring safety
lever (6) is engaged. If not, push safety lever (6) outward to engage (Fig J). Always check battery
compartment (5) cannot be pulled out without disengaging safety lever (6).
5. Secure battery compartment (5) by re-inserting screw and using a small screwdriver*,
tighten compartment screw in a clockwise direction.
Using the Remote Control in an open area
NOTE: This remote control controls both lights at the same time. They do not operate
independently.
When using remote control, range area is 8m when there is unrestricted path with no obstacles.
For best use, ensure you aim remote control directly at LED with no obstacles in the path of signal
from the remote to the LED.
NOTE: For use of the LED light when submerged in water, refer to next section
1. Turn LED light on by pressing On button (6).
2. To change colour of lights, press on relevant colour selection (8) button.
3. To increase brightness of selected colour press on increase brightness (13) button.
4. To decrease brightness of selected colour press on decrease brightness (12) button.
5. FADE Function: When pressing on Fade (10) button, LED light will fade from one colour to
next through 13 colours. To stop fade function, press either reset button (12) or other colour
button.
NOTE: Reset button will always reset LED light to colour red.
6.
JUMP Function: When pressing on jump (11) button, LED light will jump / change from
one colour to next through 13 colours continuously. To stop jump function, press either reset
button (12) or other colour button.
NOTE: Reset button will reset the LED light to red.
7. To turn LED light o, press O button (8).
Using the Remote Control when the LED Light is
submersed in water.
WARNING: Do not submerse in ponds, or bodies of water where there are animals or children
present. Do not use in Fish Ponds or aquariums.
NOTE: Ensure the USB Port rubber plug (17) is plugged into the USB charge port (2) (Fig D) before
placing into water. This ensures there is no water ingress when the LED light is placed in water.
When submersing the LED light in water, the control range area is limited to a depth of
approximately 40cm, hence if placing in more than 40cm it is recommended to turn on LED light
and set to function / colour required before exceeding 40cm. LED light will continue to function
on set colour / function after being submersed more than 40cm, however, changes to colour
/ function, or turning unit o, can only be done when unit is within 40cm submersed remote
control range.
NOTE: After use in water, ensure the LED is removed from the water and dried for next use or
for charging.
Service Support
If you are having diculty in using your product, you can nd instructional Know How videos on
our website, https://help.tools/ by clicking on the How To product. If you have any issues with
the operation of your product, call us on 1300 889 028 for advice or email us at
info.aldi@positecgroup.com
Parts List
1. LED (x 10)
2. USB Charge Port
3. USB Charging light
4. Remote Control
5. Remote Control
battery compartment
(with battery included)
6. Safety Lever
7. On button
8. O button
9. Colour Selection
10. Fade
11. Jump
12. Reset
13. Decrease brightness
14. Increase brightness
15. Safety Screw
16. USB Charging cable
17. USB Port rubber plug
1.
Correct placement
at side up
Incorrect placement
curved side up
K. L.
4. 5.
7.
16.
17.
2.
6.
12.
10.
8.
9.
11.
14.
15.
13.
B. C. D.
A.
3.
RED LIGHT =
CHARGING
GREEN LIGHT =
CHARGED
E.
F. G.
I.
H. J.
* Not supplied
2

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Lightway FPC-088 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info