Bedienungsanleitung Line 6 Firehawk FX (Seite 13 von 16) (Englisch)

693634

Zoom out

Zoom in

Vorherige Seite

1/16

Nächste Seite

To reverse playback of your loop: Press and hold the Looper switch

for ~2 seconds while the loop is playing. Press and hold the Looper

switch again to revert back to non-reverse playback.

To stop Looper playback: Double-tap the Looper footswitch. The

LED stops ashing and turns bright white, indicating a loop is stored in

memory. Press the Looper footswitch again to restart playback of the

stored loop.

To delete the recorded loop and start from scratch: Stop the Looper

and press and hold the footswitch for ~2 seconds. The LED returns to

dim white, indicating there is no loop in memory.

Output Modes

The OUTPUT MODE switch found on the Firehawk FX rear panel

cleverly congures the audio signals sent out the XLR and 1/4-inch

outputs to optimize them for your setup:

• Line Out Mode optimizes the guitar sound for direct recording and

full-range monitoring. The signal is at line level and simulates the

sound of a mic’d amp out of both the XLR and 1/4” outputs.

• Amp Out Mode is very dierent in that the guitar sound is

optimized for connecting into the front of a guitar amp. The signal

is at instrument level and is not appropriate to monitor through

headphones or a full range system, therefore, the guitar signal is

only present at the 1/4” outputs in this mode.

• Because Bluetooth

streamed audio does not typically sound best

playing through a guitar amp, the 1/4” outs carry only the guitar

signal when in Amp Out Mode – Bluetooth

audio is only present

at the XLR and Headphone outs in this mode.

As shown in the following table, the guitar audio signal is optimized for

a full range system versus for a guitar amp, and the level for each signal

also changes with the LINE and AMP Output Mode settings.

LINE MODE AMP MODE

XLR Output

Audio

Guitar Tone is Studio/Direct optimized

Includes Bluetooth streamed playback

Bluetooth streamed playback

only

XLR Output

Level

8.219 dBu / 6.0 dBv 8.219 dBu / 6.0 dBv

1/4” Output

Audio

Guitar Tone is Studio/Direct optimized

Includes Bluetooth streamed playback

Guitar Tone only - Ampliﬁer

optimized

1/4” Output

Level

Line level Instrument level

LINE vs. AMP Mode - Audio signal type and level sent to outputs

NOTE: In either OUTPUT MODE setting, the PHONES output always

receives the same audio as the XLR outputs.

Live Edit Mode

The Live Edit Mode allows you quick access to the individual FX

parameters on the Firehawk FX device as an alternative to using the

Firehawk Remote app for adjusting your FX settings. The steps are as

follows.

Editing FX Parameters

• Enter Live Edit Mode by simultaneously pressing both the

Bank Up  and Bank Down  footswitches. The two rows of

footswitches, FS1–FS5 and A–D, will alternate ashing. You'll see

abbreviations for the processing blocks accessible for each row of

footswitches are displayed in the LCD to help you choose what you

want to edit. As indicated, the FX and Looper blocks are accessed

via FS1–FS5 and the Amp, Cab & EQ are accessed via A–C.

DRV REV MOD DLY LPR AMP CAB PEQ

The LCD displays the editable blocks for the row of ashing

footswitches

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Line 6 Firehawk FX Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Line 6 Firehawk FX

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info