602191
17
Zoom out
Zoom in
Vorherige Seite
1/80
Nächste Seite
11
Chapter 4: Connecting the ADSL2 Gateway with 4-Port Switch
Connection to a Computer
ADSL2 Gateway with 4-Port Switch
4. Connect a phone cable from the Line port on the Gateway’s back panel (see Figure 4-2) to the wall jack of
the ADSL line. A small device called a microfilter may be necessary between each phone and wall jack to
prevent interference. Contact your ISP if you have any questions.
5. Connect the power adapter to the Gateway’s Power port (see Figure 4-3), and then plug the power adapter
into a power outlet. Turn the On/Off switch to On.
The Power LED on the front panel will light up green as soon as the power adapter is connected properly
and the switch is turned on. The Power LED will flash for a few seconds, then it will light up steady when
the self-test is complete. If the LED flashes for one minute or longer, see “Appendix A: Troubleshooting.
6. Power on one of your computers that is connected to the Gateway.
The Gateway’s hardware installation is now complete.
Go to “Chapter 5: Configuring the Gateway.
Figure 4-2: ADSL Connection
Figure 4-3: Power Connection
NOTE: You should always plug the Gateway’s power
adapter into a power strip with surge protection.
NOTE: You should always change the SSID from its
default, linksys, and enable WEP encryption.
IMPORTANT: For countries that have phone jacks with RJ-11 connectors, make sure to
only place the microfilters between the phone and the wall jack and not between the
Modem and the wall jack or your ADSL will not connect.
For countries that do not have phone jacks with RJ-11 connectors (e.g. France, Sweden,
Switzerland, United Kingdom, etc.), except for ISDN users, the microfilter has to be used
between the modem and the wall jack, because the microfilter will have the RJ-11
connector.
Annex B users (E1 and DE versions of the Gateway) must use the included special cable to
connect the gateway to the wall jack (RJ-45 to RJ-12). If you require splitters or special
jacks, please contact your service provider.
17

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Linksys AG241 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info