602193
29
Zoom out
Zoom in
Vorherige Seite
1/87
Nächste Seite
23
Chapter 6: Configuring the ADSL2+ Gateway
The Setup - Advanced Routing Tab
ADSL2+ Gateway with VoIP
The Setup - Advanced Routing Tab
The Advanced Routing screen allows you to configure the NAT, dynamic routing, and static routing settings.
Advanced Routing
Operating Mode.
In this section, you will configure the Gateway’s general routing settings.
NAT. NAT is a security feature that is enabled by default. It enables the Gateway to translate IP addresses of your
local area network to a different IP address for the Internet. To disable NAT, click the Disabled option.
Dynamic Routing
With Dynamic Routing you can enable the Gateway to automatically adjust to physical changes in the network’s
layout. Using RIP, the Gateway determines the network packets’ route based on the fewest number of hops
between the source and the destination. The RIP protocol regularly broadcasts routing information to other
Gateways on the network.
RIP. If you have multiple routers, you may want to use the Routing Information Protocol (RIP) so the routers can
exchange routing information with each other. To use RIP, select the Enabled option. Otherwise, keep the default,
Disabled.
Transmit RIP Version. To transmit RIP messages, select the protocol you want: RIP1, RIP1-Compatible (RIP1
broadcasts and RIP2 multicasts), or RIP2. If you don’t want to transmit RIP messages, select None.
Receive RIP Version. To receive RIP messages, select the protocol you want: RIP1 or RIP2. If you don’t want to
receive RIP messages, select None.
Static Routing
If the Gateway is connected to more than one network, it may be necessary to set up a static route between
them. A static route is a pre-determined pathway that network information must travel to reach a specific host or
network. To create a static route, change the following settings:
Select set number. Select the number of the static route from the drop-down menu. The Gateway supports up to
20 static route entries. If you need to delete a route, then select the entry and click the Delete This Entry button.
F
i
g
u
r
e
6
-
1
4
:
A
d
v
a
n
c
e
d
R
o
u
t
i
n
g
29

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Linksys AG310 ADSL2 plus Gateway with VOIP wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info