Bedienungsanleitung Linksys BEFSR41 EtherFast Cable-DSL Router (Seite 8 von 26) (Englisch)

602199

Zoom out

Zoom in

Vorherige Seite

1/26

Nächste Seite

Chapter 2

Advanced Configuration

EtherFast Cable/DSL Router with 4-Port Switch

enter the number of minutes you want to have elapsed

before your Internet connection terminates. The default

Max Idle Time is 5 minutes.

Keep Alive: Redial Period If you select this option,

the Router will periodically check your Internet

connection. If you are disconnected, then the Router

will automatically re-establish your connection. To use

this option, select Keep Alive. In the Redial Period field,

you specify how often you want the Router to check

the Internet connection. The default Redial Period is

30 seconds.

Optional Settings

Some of these settings may be required by your ISP. Verify

with your ISP before making any changes.

Optional Settings

Host Name and Domain Name These fields allow you to

supply a host and domain name for the Router. Some ISPs,

usually cable ISPs, require these names as identification.

You may have to check with your ISP to see if your

broadband Internet service has been configured with a

host and domain name. In most cases, leaving these fields

blank will work.

MTU MTU is the Maximum Transmission Unit. It specifies

the largest packet size permitted for Internet transmission.

Select Enable if you want to manually enter the largest

packet size that is transmitted. To have the Router select

the best MTU for your Internet connection, keep the

default setting, Disable.

Size When Manual is selected in the MTU field, this option

is enabled. Leave this value in the 1200 to 1500 range. The

default size depends on the Internet Connection Type:

DHCP, Static IP, or Telstra: 1500

PPPoE: 1492

PPTP or L2TP: 1460

Network Setup

The Network Setup section changes the settings on the

network connected to the Router’s Ethernet ports. Wireless

setup is performed through the Wireless tab.

Router IP

This presents both the Router’s IP Address and Subnet

Mask as seen by your network.

•

Router IP

Network Address Server Settings (DHCP)

The settings allow you to configure the Router’s Dynamic

Host Configuration Protocol (DHCP) server function. The

Router can be used as a DHCP server for your network. A

DHCP server automatically assigns an IP address to each

computer on your network. If you choose to enable the

Router’s DHCP server option, make sure there is no other

DHCP server on your network.

Network Address Server Settings (DHCP)

Local DHCP Server DHCP is enabled by factory default.

If you already have a DHCP server on your network, or you

don’t want a DHCP server, then select Disable (no other

DHCP features will be available).

Start IP Address Enter a value for the DHCP server to

start with when is

suing IP addresses. Because the Router’s

default IP address is 192.168.1.1, the Start IP Address must

be 192.168.1.2 or greater, but smaller than 192.168.1.253.

The default is 192.168.1.100

Number of Address Enter the maximum number of

computers that you want the DHCP server to assign IP

addresses to. This number cannot be greater than 253.

The default is 50.

DHCP Address Range Displayed here is the range of

available IP addresses.

Client Lease Time The Client Lease Time is the amount

of time a network user will be allowed connection to the

Router with their current dynamic IP address. Enter the

amount of time, in minutes, that the user will be “leased”

this dynamic IP address. After the time is up, the user will

be automatically assigned a new dynamic IP address. The

default is 0 minutes, which means one day.

Static DNS 1-3

The Domain Name System (DNS) is how

the Internet translates domain or website names into

Internet addresses or URLs. Your ISP will provide you with at

least one DNS Server IP address. If you wish to use another,

enter that IP address in one of these fields. You can enter up

to three DNS Server IP addresses here. The Router will use

these for quicker access to functioning DNS servers

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Linksys BEFSR41 EtherFast Cable-DSL Router Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info