Bedienungsanleitung Linksys BEFW11S4 Wireless-B BroadBand Router (Seite 27 von 68) (Englisch)

602208

Zoom out

Zoom in

Vorherige Seite

1/68

Nächste Seite

Chapter 5: Configuring the Wireless-B Broadband Router

The Wireless Tab - Advanced Wireless Settings

Wireless-B Broadband Router

RTS Threshold. Should you encounter inconsistent data flow, only minor reduction of the default value, 2346, is

recommended. If a network packet is smaller than the preset RTS threshold size, the RTS/CTS mechanism will

not be enabled. The Router sends Request to Send (RTS) frames to a particular receiving station and negotiates

the sending of a data frame. After receiving an RTS, the wireless station responds with a Clear to Send (CTS)

frame to acknowledge the right to begin transmission. The RTS Threshold value should remain at its default value

of 2346.

Change these settings as described here and click the Save Settings button to apply your changes or Cancel

Changes to cancel your changes.

The Security Tab - Filter

Filters block specific internal users from accessing the Internet. From the Filters tab, you can set up a filter

through an IP address or a network port number.

Filter IP Address Range. To set up a filter using IP addresses, enter the range of IP addresses you wish to filter in

the IP address fields. Users who have filtered IP addresses will not be able to access the Internet at all. If you only

want to filter one IP address instead of a range of IP addresses, enter the same value into both fields. For

instance, if you wish to filter the PC with the IP address of 192.168.1.5, enter 5 into both fields on one line:

192.168.1.5 ~ 192.168.1.5.

Filter Port Range. To filter users by network port number, select a protocol, then enter a network port number or a

range of network ports. Enter the port numbers you want to filter in the port numbers fields. Users connected to

the Router will no longer be able to access any port number listed there.

Filter MAC Address. This feature filters the Ethernet adapter’s specific MAC address from going out to the

Internet. To check your Ethernet adapter’s MAC address, you can run winipcfg or ipconfig in the command

prompt, depending on which Windows operating system you are using. To set the MAC filter, click the Edit MAC

Filter Setting button. When the screen appears, select the range in the drop-down menu, and in a MAC number

field, enter the 12-digit MAC address you want to filter. Click Apply to save the changes, or Undo to undo the

changes. For information on obtaining a MAC address, go to Appendix E: Finding the MAC Address and IP Address

for Your Ethernet Adapter.

Block WAN Requests. Enable the Block WAN Request feature by checking the radio button beside Block

Anonymous Internet Requests and you can prevent your network from being “pinged,” or detected, by other

Internet users. Click Disabled it you want to allow anonymous Internet requests.The Block WAN Request feature

also reinforces your network security by hiding your network ports. Both functions of the Block WAN Request

Figure 5-21: Security Tab - Filter

Figure 5-22: Security Tab - MAC Filter

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Linksys BEFW11S4 Wireless-B BroadBand Router Seite 27

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info