Bedienungsanleitung Linksys BEFW11S4 Wireless-B BroadBand Router (Seite 39 von 68) (Englisch)

602208

Zoom out

Zoom in

Vorherige Seite

1/68

Nächste Seite

Appendix A: Troubleshooting

Common Problems and Solutions

Wireless-B Broadband Router

C. In the command prompt, type ping followed by your Internet or Internet IP address and press the Enter

key. The Internet or Internet IP Address can be found on the Status screen of the Router’s web-based utility.

For example, if your Internet or Internet IP address is 1.2.3.4, you would enter ping 1.2.3.4 and press the Enter

key.

• If you get a reply, the computer is connected to the Router.

• If you do NOT get a reply, try the ping command from a different computer to verify that your original

computer is not the cause of the problem.

D. In the command prompt, type ping www.yahoo.com and press the Enter key.

• If you get a reply, the computer is connected to the Internet. If you cannot open a webpage, try the ping

command from a different computer to verify that your original computer is not the cause of the problem.

• If you do NOT get a reply, there may be a problem with the connection. Try the ping command from a

different computer to verify that your original computer is not the cause of the problem.

5. I am not getting an IP address on the Internet with my Internet connection.

• Refer to “Problem #2, I want to test my Internet connection” to verify that you have connectivity.

1. If you need to register the MAC address of your Ethernet adapter with your ISP, please see “Appendix

E: Finding the MAC address and IP Address for Your Ethernet Adapter.” If you need to clone the MAC

address of your Ethernet adapter onto the Router, see the System section of “Chapter 5: Configuring

the Wireless-B Broadband Router” for details.

2. Make sure you are using the right Internet connection settings. Contact your ISP to see if your Internet

connection type is DHCP, Static IP Address, or PPPoE (commonly used by DSL consumers). Please

refer to the Setup section of “Chapter 5: Configuring the Wireless-B Broadband Router” for details on

Internet connection settings.

3. Make sure you have the right cable. Check to see if the Internet column has a solidly lit Link/Act LED.

4. Make sure the cable connecting from your cable or DSL modem is connected to the Router’s Internet

port. Verify that the Status page of the Router’s web-based utility shows a valid IP address from your

ISP.

5. Turn off the computer, Router, and cable/DSL modem. Wait 30 seconds, and then turn on the Router,

cable/DSL modem, and computer. Check the Status tab of the Router’s web-based utility to see if you

get an IP address.

6. I am not able to access the Setup page of the Router’s web-based utility.

• Refer to “Problem #2, I want to test my Internet connection” to verify that your computer is properly

connected to the Router.

1. Refer to “Appendix E: Finding the MAC Address and IP address for Your Ethernet Adapter” to verify

that your computer has an IP Address, Subnet Mask, Gateway, and DNS.

2. Set a static IP address on your system; refer to “Problem #1: I need to set a static IP address.”

3. Refer to “Problem #10: I need to remove the proxy settings or the dial-up pop-up window (for PPPoE

users).”

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Linksys BEFW11S4 Wireless-B BroadBand Router Seite 39

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info