Bedienungsanleitung Linksys LRT224 (Seite 36 von 77) (Englisch)

727826

Zoom out

Zoom in

Vorherige Seite

1/77

Nächste Seite

System Management

Linksys

Service: This is to select the Binding Service Port to be activated.

The default (such as ALL-TCP&UDP 0~65535, WWW

80~80, FTP 21 to 21, etc.) can be selected from the pull-

down option list. The default Service is All 0~65535.

Option List for Service Management: Click the button

to enter the Service Port configuration page to add or

remove default Service Ports on the option list.

Source IP: Users can assign packets of specific Intranet virtual IP to

go through a specific WAN port for external connection.

In the boxes here, input the Intranet virtual IP address

range; for example, if 192.168.1.100~150 is input,

the binding range will be 100~150. If only specific

Service Ports need to be designated, while specific IP

designation is not necessary, input “0” in the IP boxes.

Destination IP: In the boxes, input an external static IP address. For

example, if connections to destination IP address

210.11.1.1 are to be restricted to WAN1, the external

static IP address 210.1.1.1 ~ 210.1.1.1 should be input. If

a range of destinations is to be assigned, input the range

such as 210.11.1.1 ~ 210.11.255.254. This means the

Class B Network Segment of 210.11.x.x will be restricted

to a specific WAN. If only specific Service Ports need to be

designated, while a specific IP destination assignment is

not required, input “0” into the IP boxes.

Interface: Select the WAN for which users want to set up the

binding rule.

Enable: To activate the rule.

Add To List: To add this rule to the list.

Delete To remove the rules selected from the Service List.

Moving Up & Down: The priority for rule execution depends on the rule order

in the list. A rule located at the top will be executed prior

to those located below it. Users can arrange the order

according to their priorities.

Add New: Click the button to start a new entry.

Note The rules configured in Protocol Binding will be executed by the device

according to their priorities too. The higher up on the list, the higher the priority

of execution.

Adding a service

To add a new service item or to edit an existing service, click Service

Management. If the web browser displays a warning about the pop-up

window, click to allow the blocked content.

In the Service Management window, add or edit entries as needed. After setting

a rule, be sure to click OK to save your settings or click Cancel to undo them. To

add a service to the list: Enter the following information, and then click Add to

List. You can have up to 30 services in the list.

o Service Name: Give a name to the service.

o Protocol: Choose the required protocol. TCP, UDP or Ipv6 can be chosen.

o Port Range: Enter the port range.

• To add another new service: Enter the information, and then click Add

to list.

• To edit a service you created: Select the service in the list and then click

Update to make the changes. If you do not need to make changes, click

Add New to de- select the service and clear the text fields.

• To delete a service from the list : Click Delete to delete an existing service.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Linksys LRT224 Seite 36

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info