Bedienungsanleitung Linksys WAP54Gv3-EU_qi (Seite 19 von 45) (Englisch)

55513

Zoom out

Zoom in

Vorherige Seite

1/45

Nächste Seite

Chapter 3

Configuration

Wireless-G Access Point

The Wireless Tab > Wireless MAC Filter

This screen allows you to permit or block wireless access

for computers with specific MAC addresses.

Wireless > Wireless MAC Filter

Wireless MAC Filter

Access Restriction

If you want to control access to your wireless network,

select Enable. If you do not wish to filter users by MAC

address, select Disable.

To deny access, click Prevent PCs listed below from

accessing the wireless network. To permit access,

click Permit PCs listed below to access the wireless

network.

MAC 01-25 Enter the MAC addresses of the computers

whose access you want to control. If you want to list more

than 25 MAC addresses, then select MAC Addresses

26~50 from the drop-down menu.

Click Clear to delete the MAC addresses you have

entered.

Change these settings as described here and click Save

Settings to apply your changes, or click Cancel Changes

to cancel your changes. Click Help for more information.

The Wireless Tab > Advanced Wireless

Settings

This screen allows you to configure the advanced settings

for the Access Point. In most cases, these settings do not

need to be changed.

Wireless > Advanced Wireless Settings

Advanced Wireless

You can change the data transmission and output power

settings for the Access Point.

Authentication Type Select the authentication method

you want the Access Point to use, Shared Key or Open

System (Default). Shared Key is when both the sender

and the recipient share a WEP key for authentication.

Open System is when the sender and the recipient do not

share a WEP key for authentication. All devices on your

network must use the same authentication type. In most

cases, keep the default, Open System (Default).

Basic Rates This setting is not actually one rate of

transmission but a series of rates that are advertised

to the other wireless devices in your network, so they

know at which rates the Access Point can transmit. At

the Default setting, the Access Point will advertise that

it will automatically select the best rate for transmission.

Other options are 1-2Mbps, for use with older wireless

technology, and All, when you wish to have all rates

advertised. The Basic Data Rates are not the rates

transmitted; the rates transmitted can be configured

through the Transmission Rates setting on this screen.

Transmission Rates The range is from 1 to 54Mbps.

The rate of data transmission should be set depending

on the speed of your wireless network. You can select

from a range of transmission speeds, or you can keep the

default setting, Auto (Default), to have the Access Point

automatically use the fastest possible data rate and enable

the Auto-Fallback feature. Auto-Fallback will negotiate the

best possible connection speed between the Access Point

and a wireless client.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Linksys WAP54Gv3-EU_qi Seite 19

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Linksys WAP54Gv3-EU_qi

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info