612980
10
Zoom out
Zoom in
Vorherige Seite
1/41
Nächste Seite
Chapter 3
Advanced Configuration
7
Wireless-N Access Point with Dual-Band
b. Within two minutes, click the Wi-Fi Protected
Setup button on the Access Point’s Wi-Fi Protected
Setup screen.
c. After the client device has been configured, click
OK. Then refer back to your client device or its
documentation for further instructions
Congratulations
The Wi-Fi Protected Setup Status, Wireless Band,
Network Name (SSID), and Security method are
displayed at the bottom of the screen.
2. Enter Wi-Fi Protected Setup PIN from Client
device Use this method if your client device has a Wi-Fi
Protected Setup PIN number.
a. Enter the PIN number in the field on this screen.
b. Click Register.
c. After the client device has been configured, click
OK. Then refer back to your client device or its
documentation for further instructions
Congratulations
The Wi-Fi Protected Setup Status, Wireless Band,
Network Name (SSID), and Security method are
displayed at the bottom of the screen.
3. Enter Wi-Fi Protected Setup PIN from Access Point
on Client device Use this method if your client device
requests the Access Point’s PIN number.
a. On the client’s Wi-Fi Protected Setup screen, enter
the PIN number listed on the Access Point’s Wi-Fi
Protected Setup screen. Then click Register or the
appropriate button. (The PIN number is also listed
on the label on the bottom of the Access Point.)
b. After the client device has been configured, click
OK. Then refer back to your client device or its
documentation for further instructions
Congratulations
The Wi-Fi Protected Setup Status, Wireless Band,
Network Name (SSID), and Security method are
displayed at the bottom of the screen.
Wireless > Wireless MAC Filter
Wireless access can be filtered by specifying the MAC
addresses of wireless devices within range of your network.
Wireless > Wireless MAC Filter
Wireless MAC Filter
Enabled/Disabled To filter wireless users by MAC
Address, either permitting or blocking access, select
Enabled. If you do not wish to filter users by MAC Address,
keep the default setting, Disabled.
Access Restriction
Prevent Select this to block wireless access by MAC
Address. This option is selected by default.
Permit Select this to allow wireless access by MAC
Address. This option is not selected by default.
MAC Address Filter List
Wireless Client List Click this to open the Wireless Client
List screen.
10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Linksys WAP610N wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info