Bedienungsanleitung Linksys WRT150N - Wireless-N home router (Seite 57 von 90) (Englisch)

495211

Zoom out

Zoom in

Vorherige Seite

1/90

Nächste Seite

Appendix A: Troubleshooting

Common Problems and Solutions

Wireless-N Home Router

B Open a command prompt.

For Windows 98SE and Me:

• Click Start and Run. In the Open field, type command. Press the Enter key or click the OK button.

For Windows 2000 and XP:

• Click Start and Run. In the Open field, type cmd. Press the Enter key or click the OK button. In the

command prompt, type ping 192.168.1.1 and press the Enter key.

• If you get a reply, the computer is communicating with the Router.

• If you do NOT get a reply, please check the cable, and make sure Obtain an IP address automatically is

selected in the TCP/IP settings for your Ethernet adapter.

C In the command prompt, type ping followed by your Internet or WAN IP address and press the Enter key.

The Internet or WAN IP Address can be found on the Status screen of the Router’s web-based utility. For

example, if your Internet or WAN IP address is 1.2.3.4, you would enter ping 1.2.3.4 and press the Enter key.

• If you get a reply, the computer is connected to the Router.

• If you do NOT get a reply, try the ping command from a different computer to verify that your original

computer is not the cause of the problem.

D In the command prompt, type ping www.yahoo.com and press the Enter key.

• If you get a reply, the computer is connected to the Internet. If you cannot open a webpage, try the ping

command from a different computer to verify that your original computer is not the cause of the problem.

• If you do NOT get a reply, there may be a problem with the connection. Try the ping command from a

different computer to verify that your original computer is not the cause of the problem.

4. I am not getting an IP address on the Internet with my Internet connection.

• Refer to “Problem #3, I want to test my Internet connection” to verify that you have connectivity.

• If you need to register the MAC address of your Ethernet adapter with your ISP, please see “Appendix E:

Finding the MAC address and IP Address for Your Ethernet Adapter.” If you need to clone the MAC address

of your Ethernet adapter onto the Router, see the System section of “Chapter 5: Configuring the

Wireless-N Home Router” for details.

• Make sure you are using the right Internet connection settings. Contact your ISP to see if your Internet

connection type is DHCP, Static IP Address, or PPPoE (commonly used by DSL consumers). Please refer to

the Setup section of “Chapter 5: Configuring the Wireless-N Home Router” for details on Internet

connection settings.

• Make sure you have the right cable. Check to see if the Internet column has a solidly lit Link/Act LED.

• Make sure the cable connecting from your cable or DSL modem is connected to the Router’s Internet port.

Verify that the Status page of the Router’s web-based utility shows a valid IP address from your ISP.

• Turn off the computer, Router, and cable/DSL modem. Wait 30 seconds, and then turn on the Router,

cable/DSL modem, and computer. Check the Status tab of the Router’s web-based utility to see if you get

an IP address.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Linksys WRT150N - Wireless-N home router Seite 57

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Linksys WRT150N - Wireless-N home router

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info