Bedienungsanleitung Linksys WRT54 (Seite 27 von 81) (Englisch)

97358

Zoom out

Zoom in

Vorherige Seite

1/81

Nächste Seite

Chapter 6: Configuring the Wireless-G Broadband Router

The Setup Tab - Advanced Routing

Wireless-G Broadband Router

The Setup Tab - Advanced Routing

This tab is used to set up the Router’s advanced functions. Operating Mode allows you to select the type(s) of

advanced functions you use. Dynamic Routing will automatically adjust how packets travel on your network. Static

Routing sets up a fixed route to another network destination.

Operating Mode

. Select the mode in which this Router will function. If this Router is hosting your network’s

connection to the Internet, select

Gateway

. If another Router exists on your network, select

Router

. When Router is

chosen,

Dynamic Routing

will be enabled.

Dynamic Routing

. The Dynamic Routing feature enables the Router to automatically adjust to physical changes in

the network’s layout and exchange routing tables with the other router(s). The Router determines the network

packets’ route based on the fewest number of hops between the source and the destination. This feature is

Disabled by default. From the drop-down menu, you can also select,

LAN & Wireless

, which performs dynamic

routing over both your Ethernet and wireless networks. You can also select,

WAN

, which performs dynamic routing

with data coming from the Internet. Finally, selecting

Both

performs dynamic routing with both methods described.

Static Routing

. To set up a static route between the Router and another network, select a number from the Static

Routing drop-down list. (A static route is a pre-determined pathway that network information must travel to reach a

specific host or network.) Enter the information described below to set up a new static route. (Clicking the

Delete

This Entry

will delete a static route.)

Enter Route Name

. Enter a name for the Route here, using a maximum of 25 alphanumeric characters.

Destination LAN IP

. The Destination LAN IP is the address of the remote network or host to which you want to

assign a static route.

Subnet Mask

. The Subnet Mask determines which portion of a Destination LAN IP address is the network

portion, and which portion is the host portion.

Default Gateway

. This is the IP address of the gateway device that allows for contact between the Router and

the remote network or host.

Interface

. This interface tells you whether the Destination IP Address is on the

LAN & Wireless

(Ethernet and

wireless networks), the

WAN

(Internet), or

Loopback

(a dummy network in which one PC acts like a network-

necessary for certain software programs).

Click the

Show Routing Table

button to view the Static Routes you’ve already set up.

Change these settings as described here and click the

Save Settings

button to apply your changes or

Cancel

Changes

to cancel your changes.

Figure 6-13: Setup Tab - Advanced Routing (Gateway)

Figure 6-14: Setup Tab - Advanced Routing (Router)

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Linksys WRT54 Seite 27

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Linksys WRT54

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info