Bedienungsanleitung Livarno IAN 378535 (Seite 14 von 85) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Spanisch, Polnisch)

793229

Zoom out

Zoom in

Vorherige Seite

1/85

Nächste Seite

14 GB/IE

Safety/Start-up

Verify the existing mains voltage matches the

required operating voltage of the lamp (see

“Technical data“) before use.

Ensure that the light does not come into contact

with water or other liquids under any circumstances.

Always unplug the lamp from the mains prior

to assembly, disassembly, cleaning or if the

lamp will not be used for extended periods.

Never open any of the components of the elec-

trical equipment or insert any objects into the

same components. This will pose a risk of fatal

injury from electric shock.

The illuminant in this light must be replaced by

the manufactured or an authorised technician

or similarly qualiﬁed person.

This light is not suitable for dimmer

or electronic switches.

Prevent fire and injury hazards

Do not look into the illuminant from a close

distance during operation.

Do not look at the LED with an optical instrument

(e.g. magniﬁer).

Do not cover the lamp or the mains plug with

objects. Excessive heat can result in a ﬁre.

Do not operate the lamp unattended.

For your safety

Mount the light so that it is protected from

moisture and dirt.

Always be attentive! Always pay attention to

what you are doing and always proceed with

caution. Never mount or use the light if you are

having diﬃculty concentrating or do not feel well.

In order to disconnect the light completely from

the power supply, the mains plug must be

removed from the socket.

Start-up

Installing the light

Note: Remove all packaging materials from the

product.

Note: During assembly, make sure that you pull the

power cord 3 slowly through the base 1.

Carefully remove the bottom of the base 1b

(see Fig. A).

Insert the standpipe 2 into the base 1 (see

Fig. B). Make sure that the power cord

which

runs through the standpipe 2, is not pinched.

First slide the washer 4, then the toothed

washer 4 and ﬁnally the nut 6 onto the

standpipe 2 from below (see Fig. C).

Then tighten the nut 6 using the tool 7 (see

Fig. C). Pay attention to the correct ﬁt. Place

the power cord 3 in the base 1 as shown in

Figure D. Make sure that the power cord 3 is

not pinched inside the base 1.

Then place the assembled lamp on the bottom

of the base 1b . Make sure that the power cord

3 is in the recess provided on the underside

of the base 1b (see Fig. E).

Screw the bottom of the stand 1b tight with the

screws 8 provided (see Fig. F).

Glue the screw covers 9 to the intended loca-

tion on the screws 8 (see Fig. G).

Insert the mains plug 13 into a properly installed

socket (see Fig. H).

The lamp is now ready for use.

Switch the lamp on and oﬀ

Switch the light on or oﬀ using the ON/OFF

switch 12 (see Fig. H).

Adjusting the reﬂector

CAUTION! RISK OF BURNS DUE TO

HOT SURFACES!

Note: Only change the position of the reﬂector 10

if the lamp is turned oﬀ.

Start-up/Maintenance and cleaning/Disposal/Guarantee and service

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Livarno IAN 378535 Seite 14

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info