783946

Livington Instant Heater M23726 Seite 5

5
Zoom out
Zoom in
Vorherige Seite
1/12
Nächste Seite
5
Indoors, the Livington Instant Heater only warms up yourself and objects
such as carpets and furniture. Since the air is not heated, no dryness occurs.
OUTDOORS
The ambient air outdoors is constantly moving. A circulation heater proves
to be impractical here, because the heated air is simply blown away - the
heating effect, which is supposed to supply you with heat, does not work.
However, the Livington Instant Heater allows you to heat certain areas
outdoors and keep objects and people around the heater warm with
maximum heating efficiency.
WALL MOUNTING
CAUTION:
The device is fitted with a tilt sensor that ensures that the Livington
Instant Heater will only work if it is correctly installed. If the correct
angle of inclination is not maintained, e.g. if the device hangs crookedly or
lies on the floor, this inclination sensor prevents it from being switched on,
and Error E2 or 23 is displayed. It is only possible to switch on or operate the
Livington Instant Heater after it has been installed at the correct angle.
• The Livington Instant Heater may only be attached horizontally to
the wall. If you are using a standard plug connection, the help of an
electrician is not required for installation. An electrician is only necessary
if the heater is to be hard-wired to the wall.
• DO NOT install the heater on flammable surfaces.
• The underside of the heater must be at a minimum height of 1.8 m above
the floor so that the heater cannot be touched accidentally when it is in
operation.
• When installing the heater, it must not be installed at an angle that
exceeds 90° or falls below 45° (see installation sketch).
• NOTE: If this angle of inclination is exceeded, the heater switches off
automatically.
• Make sure that the alignment is correct. The end of the cable and the
display should be on the left side.
• Keep the power cable away from the heater, as the device heats up when
it is in operation.
• When installing the heater, make sure that the prescribed minimum
distance between the heat radiator and flammable surfaces is observed.
• The heater should always be at least 0.3 m away from the ceiling or
adjacent walls.
• Before drilling any holes, make sure that there are no wires or water pipes
in the immediate vicinity of the hole in the wall or ceiling.
• The heater must be attached to the supplied brackets.
• Secure the heater brackets securely to the surface onto which they are
installed using screws and dowels.
• Then attach the heater firmly to the brackets using the screws and nuts
provided.
• The brackets can be used to adjust the heater orientation. Adjust the
angle of inclination of the device by loosening the two wall screws.
Min: 450
Min: 300mm
Min: 300mm
Min: 1800mm
Max: 900
BASE
WALL
CEILING
WALL
WALL MOUNTING:
1. Measure and fasten so that the wall brackets are attached at a distance of
530 mm (centre holes).
2. Install the opposite bracket, but refrain from tightening the nuts.
3. Lift the heater to the height of the brackets. Then attach using the M8 nuts
and M8 rail bolts.
4. Turn the heater until it has the desired angle of inclination. Then tighten
all nuts.
OPERATING THE HEATER
• To switch the heater on, press the on/off switch on the underside of the
device, so that the display shows „0“.
• Press the temperature control on the front, the highest heating level 4
starts immediately. Press the temperature button followed by the arrow
keys on the remote control to set the desired heating level.
• Press the timer button and then use the arrow buttons to set the time until
the automatic switch-off.
• To return to standby mode, press the Standby Mode button on the remote control.
• Press the Sensor button on the remote control to set the motion sensor
mode. When motion is detected, the heater turns on for 15 minutes. If
no further movement is detected during these 15 minutes, the heating
element switches off (during this mode the display shows A-). If no
movement is detected in this mode for an hour, the heater switches to
normal standby mode.
• To reactivate the motion sensor mode, press the motion sensor button on
the remote control again.
• Pressing on the LEVEL button takes you straight to the highest heating level.
• To switch off the heater, press the on/off button on the underside of the
device.
LED DISPLAY
ON/OFF BUTTON
TEMPERATURE
REGULATOR
BATTERY
COMPARTMENT
REMOTE CONTROL
ON/OFF BUTTON
LEVEL
+
-
BATTERY REPLACEMENT
• Press the battery compartment button and slide out the battery holder.
• Remove the old battery and insert the new one. Make sure that the
positive pole of the battery is facing upward. Use only CR2025 or CR2032
batteries with the remote control.
• Push the battery holder back into the remote control, until you hear it click
into place.
Note: Always take care to ensure that no water or other liquids ever enter
the remote control.
CLEANING AND MAINTENANCE
• Always disconnect the heater‘s power supply and allow the device to cool
down before performing any maintenance work.
• DO NOT operate the device if dust or dirt has accumulated in or around the
heater.
• The heater is maintenance-free and can only be cleaned externally.
• Use a damp cloth to clean the exterior surfaces. DO NOT use strong,
aggressive or soluble cleaning agents when cleaning the heater, as these
M23725_M23726_LivingtonInstantHeater_Manual_201900803_CP.indd 5M23725_M23726_LivingtonInstantHeater_Manual_201900803_CP.indd 5 03.08.20 10:1003.08.20 10:10
… 5 …

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln
1

Forum

livington-instant-heater-m23726

Suche zurücksetzen

  • Beim Einschalten Display E2, was ist das
    a. wüthrich Eingereicht am 5-1-2024 15:17

    Antworten Frage melden

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Livington Instant Heater M23726 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info