Bedienungsanleitung Loewe Art 40 - SL3 (Seite 51 von 144) (Englisch)

645605

Zoom out

Zoom in

Vorherige Seite

1/144

Nächste Seite

Art 40-55

User manual

New recording – Manual recording (current station)

In the Timer list, New recording is selected.

 Mark recording duration.

The selection of a recording duration programmes

always a recording of the currently viewed station.

For Any station and time see below.

OK Call Timer data dialogue.

The selected recording duration is preset in the

timer data. Check timer data and correct them,

if required. In case of a previous selection of

??? Min, enter definitely the recording dura-

tion.

Mark Adopt to Timer.

OK Confirm timer data and adopt timer instruction.

Recording has been started.

New recording – Manual recording (other station)

Manual recording has been selected (see above).

 Mark Any station and time,

OK Call Station selection.

 Mark desired station,

OK Adopt station in timer data.

Check timer data and correct them, if required.

Mark Adopt to Timer.

OK Confirm timer data and adopt timer instruction.

New recording – Current programme

After calling the Current programme the timer data dialogue will be

displayed. The current programme is preset in the timer data.

Check timer data and correct them, if required.

Mark Adopt to Timer.

OK Confirm timer data and adopt timer instruction.

Recording has been started.

New recording – Following programme

After calling the Following programme the timer data dialogue will

be displayed. The following programme of the current station is preset

in the timer data.

Check timer data and correct them, if required.

Mark Adopt to Timer.

OK Confirm timer data and adopt timer instruction.

New copy job

You should copy recordings that you want to save permanently on an

external USB hard disk.

Copying recordings, which originate from a CI Plus encrypted station,

is perhaps not possible or only to a limited extent.

In the Timer list:

 Mark Create newly,

OK call.

 Mark New copy,

OK call.

The DR+ archive will be called.

For further information for exporting archive entries

refer to chapter TV, section Digital-Recorder –

Export of archive entries.

Record conflict

When programming a new recording, it can happen that there will be

an overlapping with already stored timer recordings. In this case, the

recording conflict dialogue will open.

Here you can determine which of the recordings you want to be

executed, and you must eventually specify which of the programmes

shall be fully recorded and which are cut.

 Select recording,

OK change status.

The symbol before the recording shows you what

happens to the recording.

If the status for each recording is ok:

 Mark store recordings,

OK call.

The timer data of the recordings will be adjusted

accordingly.

Explanation of the symbols in the conflict manager:

TV programme is completely recorded.

Recording is cut off (at the beginning and/or end). Pay

attention to the start and end time of the recording.

The recording is deleted.



Timer

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Loewe Art 40 - SL3 Seite 51

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Loewe Art 40 - SL3

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info