Bedienungsanleitung Loewe Art 50 (Seite 125 von 154) (Englisch)

548740

125

Zoom out

Zoom in

Vorherige Seite

1/154

Nächste Seite

Art 40-60

User guide

125



Teaching the remote control

By means of key code 18 (Set-Top Box data base) your remote control

Assist may be taught for your Set-Top Box (e.g., decoder, external cable

tuner). Thus, you spare yourself the use of several remote controls.

For the use of 2-digit key codes see chapter External devices,

section Operating Loewe units.

The following options are available for teach-in:

- Entering a 3-digit code number

- Set-Top Box read-out

- Teaching individual keys

- Delete learned codes

In the following, the STB key is dealt with as an example since

device code 18 is preset for this key ex-works. Code 18 may also be

assigned to the AUDIO and RADIO keys; the following description

applies accordingly.

Entering a 3-digit code number

The STB key can be programmed directly by means of a device-

dependent 3-digit code. You find a list of these codes in chapter Code

page at the end of this instruction manual.

Keep the STB and OK keys depressed for five seconds.

The LED above the STB key flashes twice.

Enter the 3-digit code from the list. The LED above the

STB key lights up for 1 second.

OK end the programming mode. After a successful

programming the LED flashes twice.

When entering a wrong code number, the LED lights

up for 2 seconds. Do this programming once again.

Read-out of programmed Set-Top Box

The code of the currently programmed device on the STB key can be

indicated by the remote control.

Keep the STB and OK keys depressed for five seconds.

The LED above the STB key flashes twice.

Press INFO key.

The LED above the STB key shows the programmed

code by flashing. The figure "0" will be indicated by

flashing 5 times.

Teaching individual keys

All keys (except the TV, STB, VIDEO and AUDIO device keys as well

as the V+/- keys

and ) can be taught for the operation of units

which are not contained in the integrated data base. The functions of

the selected button are then completely or partially overwritten with

the new codes.

Place the TV remote control and the remote control to be replaced

in such a way that the infrared windows face each other at a distance

of 1-5 cm (see sketch).

Keep the STB and the red key simultaneously

depressed for five seconds. The LED above the STB

key lights up permanently.

Press key to be taught on the TV remote control.

The LED above the STB key flashes.

On the original remote control press the button

which is to be taught.

The LED above the selected STB key flashes twice.

If the code is not correctly recognised, the LED above

the STB key flashes ten times. Then repeat your entry

on the original remote control. If necessary correct the

allocation of the two remote controls. Continue with

the other buttons as described above.

To end the teaching mode, press the STB key again.

After 10 seconds without an entry the teaching mode

is automatically terminated.

It is possible that not all remote control codes can

be taught.

You can make a note of the functions, which you

have allocated to the keys, on the notes pages at the

end of this instruction manual.

1-5 cm

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Loewe Art 50 Seite 125

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Loewe Art 50

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info