548741
110
Zoom out
Zoom in
Vorherige Seite
1/154
Nächste Seite
Art 40-60
User guide
110
System settings
Multimedia / Network
Configuration of the built-in LAN adaptor
The network wizard was called via the network ac-
cess setting On, wired only.
IP configuration
 Select type of IP configuration.
automatic: Automatic configuration of the IP
address via DHCP server or via multiple
protocols according to UPnP specifica-
tion (including DHCP).
OK proceed to network status (see below).
manual: Enter your fixed static IP addresses
manually (see below).
OK proceed to Manual IP configuration.
Manual IP configuration
If manual has been selected under IP configuration:
 Enter IP, Subnet mask, Gateway and DNS server
addresses in succession with the numerical keys
on the remote control.
proceed to network status.
Network status
You see the current network status again.
BACK: End of wizard.
.
...
IP address 192.168.000.123
Subnet mask 255.255.255.000
Gateway 192.168.000.100
DNS server 1 192.168.000.010
DNS server 2 192.168.001.010
Back with Proceed with
Netzworking
Manual IP configuration
Please specify the static IP address of the network adapter.
Configuration of the built-in WLAN bridge adaptor
The network wizard was called via the network
access setting On, wireless only or Wireless +
bridge function.
Search for Access points
The TV set now searches for wireless routers.
BACK: Stop search.
Access point selection
After the end of the search:
 Select required access point from the options
found.
OK Proceed to entry of WLAN password.
No access point found
If the desired access point is not found:
 Mark Search again,
OK repeat search for wireless routers.
Or:
 Mark Enter access point manually,
OK
enter manually the SSID of the desired access
point, e.g., when the SSID of the access point is
not transferred.
OK Proceed to entry of WLAN password.
WLAN password (WPA password / WEP password / WEP index)
If your wireless network is not encrypted: Proceed to
IP configuration.
Enter WLAN password.
In case of an unknown WLAN key, contact your
network administrator.
For encryption types supported, see chapter Tech-
nical data, section Media.
For WEP encryption
 Select the WEP index,
OK proceed to IP configuration.
IP configuration
 Select type of IP configuration.
For the further workflow of the network wizard
see left column under IP configuration.
Network status
At the end of the network wizard you see your current
network status again.
BACK: End of wizard.
110

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln
1

Forum

loewe-art-60

Suche zurücksetzen

  • Wie startet man den manuellen Sendersuchlauf bei Loewe Art 60?
    Eingereicht am 14-2-2022 22:23

    Antworten Frage melden

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Loewe Art 60 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Andere Handbücher von Loewe Art 60

Loewe Art 60 Bedienungsanleitung - Deutsch - 154 seiten

Loewe Art 60 Bedienungsanleitung - Holländisch - 46 seiten

Loewe Art 60 Bedienungsanleitung - Französisch - 154 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info