Bedienungsanleitung Loewe Connect 32 3D (Seite 131 von 156) (Englisch)

475107

131

Zoom out

Zoom in

Vorherige Seite

1/156

Nächste Seite

131 -

english

Problem Possible cause Remedy

All menus are displayed in the wrong

language.

The menu language was set incorrectly. Set the menu language:

Press the MEDIA button in TV mode. In the MediaPortal,

highlight the last menu item (Index) in the upper half and

call up with OK. Mark the first key word and call it with

OK. Then select the language and confirm it with OK.

In the TV menu, Connections cannot be

called (displayed in grey ).

A timer recording is in progress. Wait until the timer recording ends or delete the

timer recording (page 123).

The control functions of the Loewe

Recorder and the Timer are not working

or are not working properly

a) The Digital Link function is not activated or

not possible in the recorder.

b) EURO-AV cable is not connected.

a) Activate Digital Link in the recorder (see operat-

ing instructions of the recorder).

b) Connect EURO-AV cable (page 111).

General problems when connecting

external devices via an AV input.

a) The AV standard is set incorrectly.

b) The signal type is set incorrectly.

a) Set the correct standard (page 108).

b) Set the correct signal type (page 108).

If AV standard or AV signal is set to “Automatic”

then this can cause errors to be detected with

signals that do not comply with standards. In this

case standard and signal must be set according to

the information in the operating manual of the

external device.

The connection of a decoder does not

function or does not function properly.

a) The signal is not decoded because the correct

decoder stations are not selected in the menu.

b) The sound is missing in decoder mode becau-

se the wrong decoder sound is assigned in the

menu.

a) Select the right decoder stations in the menu (TV

menu ט Connections ט Miscellaneous ט Decoder

stations ט Select decoder station(s) (see page 109).

b) Select the right sound code (always, never, automa-

tic) in the menu (TV menu

ט Connections ט

Miscellaneous ט Decoder stations ט Sound encodig),

see also decoder instructions.

Digital Link Plus does not work. a) EURO-AV cable is not fully wired (pin 10 not

wired).

b) Some recorders can only adopt stations

during the initial installation of the TV set.

a) Replace the EURO-AV cable.

b) Restore the recorder to the as-delivered state

(see recorder’s operating manual).

With Teletext various characters are

displayed incorrectly.

The wrong character set has been set in the

Teletext menu.

Set the right character set: Select Teletext menu ט

Settings ט Character set ט Standard or the

appropriate character set.

Errors occurred when running a CA

module.

Switch the TV set off. Remove the CA-module from

the TV set. Wait a few seconds. Reinsert the CA-

module. Switch the TV set on again.

Troubleshooting

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Loewe Connect 32 3D Seite 131

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Loewe Connect 32 3D

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info