Bedienungsanleitung Loewe mimo l 20 (Seite 11 von 28) (Englisch)

143121

Zoom out

Zoom in

Vorherige Seite

1/28

Nächste Seite

11 -

Initial installation Daily operation

Switch on from stand-by

On the set:

If the LED on the set glows red or orange:

Press the display window to switch the set on.

If the red LED on the set is not alight:

Press the On / Off button (mains voltage) on the right hand

side of the set.

Switch to stand-by:

Press the display window, the LED changes colour from green

to red.

Switch on/off with the remote control

The set is on stand-by, the red LED is alight:

Press the blue on/off button on the remote control to switch

on the set or ...

with a numeric key (0 – 9) or ...

wxyz

with the OK button.

The green operating LED then lights up.

Switch on radio mode:

(see also page 18).

Press the Radio button.

RADIO

Switch off radio mode:

Press the Radio button again or ...

RADIO

press the button END.

END

(

Directing DVB-T antenna

(only for DVB-T models)

If you use a room antenna to receive one or more DVB-T stations that have

picture and sound interference, then you should change the location of where

the antenna is set up.

To help you direct your antenna or to help you determine the most suitable loca-

tion to set up the antenna, your TV set has a display for the signal quality C/N

and the signal strength Level.

Consult your specialist dealer to ﬁ nd out which channels and frequency bands

(VHF or UHF) are used to broadcast the digital TV stations in your area.

On any one channel, several digital stations are broadcast.

Select a TV channel

1. Call the “TV menu“ via the MENU button.

2. Use  to select “Settings“, then use  to select the menu line under-

neath.

3. Select “Channels“, then use  to select the menu line underneath.

4. Select “Manual settings“ and call the menu using OK

5. For digital stations, select “Signal source – DVB-T“.

6. Use the numerical buttons to specify the corresponding channel number.

When you receive a digital station, the system displays the signal quality

C/N via a bar/numeric value and the signal strength via Level. The anten-

na‘s direction or position is best when the largest values possible are

displayed (long bar) for the signal quality and signal strength.

7. Direct the antenna so that the largest numerical value/bar size is reached.

8. If no signal is found in the channel set, you can start the frequency search

run by pressing the blue button within the band selected (VHF or UHF).

9. Check the other channels one after another on which digital stations are

broadcast terrestrially in your area.

For the weakest station, direct the antenna so that the maximum numerical

value/bar size is achieved.

10. After you position or direct the antenna, we recommend to search for all the

stations using the “Search wizard“ (TV menu – Settings – Channels – Auto-

matic search).

INFO

END

Auto

Change

Manual settings

TV menu

Settings

Channels

INFO

END

Manual settings

Store

Signal source

Channel

Frequency

Name

C/N 96

DVB-T

E 05

177.50 MHz

Test

Level 99

Antenna/cabl

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Loewe mimo l 20 Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Loewe mimo l 20

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info