Bedienungsanleitung Loewe Reference lD 40 (Seite 12 von 164) (Englisch)

549215

Zoom out

Zoom in

Vorherige Seite

1/164

Nächste Seite

Reference ID 40-55

User guide

Installing the TV set

Mounting options

Your Loewe specialist dealer can assist you in finding other mounting

options that correspond to your needs. Use exclusively Loewe mount-

ing options (e.g., wall bracket, floor stand), which you will find in the

chapter Accessories, section Mounting options.

After you have decided on a mounting option, follow the directions

found in the corresponding assembly instructions.

Installation notes

Choose a place for installing your TV set where no bright light or

sunlight shines directly onto the screen. This could cause reflections

which impair the picture.

3 times the screen diagonal can be taken as a guide value for the view-

ing distance (e.g., for a 46-inch set approx. 3.5 m for SD signal). The

viewing distance can be reduced with an HD signal.

Set covers

Covers for rear and side connections

In order to remove the rear side cable cover pull them simply from

the device.

To attach the cable cover, place the lugs of the cover at the correspond-

ing cut-outs in the rear panel.

Press the cover into the cutouts until the lugs snap into the device.

Press only on the exact positions where the lugs are (see figure for the

positions), otherwise the glass rear panel may be damaged.

The side cover of the TV set can also be completely removed. For this,

open it as far as it will go and gently pull on the open cover.

The cover detaches from the holder and gives free access to the

connection area. To replace the cover, simply push it until it latches

back into place.

Connecting the TV set

Connecting to the mains supply

Remove the cover for the connections.

Connect the TV set to a 220-240V mains socket:

First plug the small plug of the power cable into the mains connection

on the back of the TV and then the large mains plug into a mains socket.

Connecting antennas

Cable (analogue) / DVB-C / DVB-T antenna:

Plug the cable of antenna, cable TV system or room antenna into the

ANT TV socket.

If you want to use analogue cables / DVB-C connection and a DVB-T

antenna together, use an external antenna switch (available from

your dealer).

Satellite antenna DVB-S:

Depending on the used satellite system, connect a connecting cable

from the multi-switch or directly from the LNC to the ANT-SAT and

ANT-SAT2 sockets of the TV set respectively.

When connecting the TV set to a single cable community antenna,

connect the ANT-SAT and ANT-SAT2 sockets directly to the appro-

priate SAT antenna socket.

When connecting the TV set to a DiSEqC single cable community

antenna (in accordance with EN 50494), connect the ANT-SAT

socket directly to the appropriate SAT antenna socket.

In case of a DiSEqC one cable communal system you require only

one antenna cable. Further distribution of the signal to the two

reception routes is accomplished by the TV set's satellite tuner.

Ask your dealer in this regard.

R TV

DVB-T DVB-SKabel

analog /

DVB-C



Preparing the TV set

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Loewe Reference lD 40 Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Loewe Reference lD 40

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info