Bedienungsanleitung Loewe xelos a20 dvb t (Seite 10 von 28) (Englisch)

143159

Zoom out

Zoom in

Vorherige Seite

1/28

Nächste Seite

- 10

Initial installation

Switch On/Off

Press the On / Off button (mains voltage) on the right hand

side of the set until it locks.

The red indicator on the TV set now lights up (standby mode).

Switch on the set with the switch integrated in the display. The

green indicator now lights up (other operating possibilities,

see page 11).

It takes about 2 minutes after switching for the screen to reach full brightness

due to the LCD technology.

If you will not be using the TV set for a long time, e.g. during a vacation, switch

it off with the On/Off button (mains voltage). The set is then disconnected from

the power supply.

Automatic programming

Automatic programming of the TV set is started the ﬁ rst time you switch it on.

Follow the menus

By pressing the OK button in the direction of the arrow

 you select the setting ...

... and conﬁ rm your settings with OK. You then go to the next

menu.

Back to the previous menu.

1. First you have to select the menu language.

In models without DVB-T, please continue with step 3.

2. Press the OK button to go to the ”Signal source” menu. If you want to re-

ceive terrestrial stations

digitally (only in DVB-T

models), select “DVB-T”,

conﬁ rm with the yellow

colour button. If you se-

lect ”Antenna/cable” as well, you can also search for and store conventional

analog stations.

3. For speciﬁ c national station sorting and pre-settings, enter the location at

which your TV is being used.

In models without DVB-T, please continue with step 5.

4. When you have selected ”DVB-T”, you go to the ”Antenna DVB-T” menu. If

you are using an active antenna, mark “yes (5V)”.

5. With OK you get an overview of which settings are to be used for the auto-

matic programming.

6. Press the OK button again to start the station search. The set searches for,

sorts and stores all receivable TV stations, according to your setting and the

connected antenna.

7. When the TV stations are stored, an appropriate message is displayed.

8. The radio stations are then searched for with OK.

9. The TV set searches for, saves and sorts all radio stations which are receiv-

able on your antenna system.

10. When the radio stations are stored, an appropriate message is displayed.

11. The station search is terminated with OK.

12. Finally log in your recorder, DVD player etc. and connect it with the TV set

(also see page 21)

You can repeat initial installation at any time, e.g. after moving house.

Call the index with the INFO button.

INFO

Select the index item “Repeat initial installation“.

Start with OK.

Channel sorting

You can change the station sorting that was carried out automatically later at

any time, see “TV menu – Settings – Channels – Change“.

Proceed

Back

Mark/unmark

Signal source

Antenna/cable

DVB-T



(

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Loewe xelos a20 dvb t Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Loewe xelos a20 dvb t

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info