770598
1
Zoom out
Zoom in
LogiLink. User Manual GD
WZ0015P
Network Cable Tester
>Package Contents
Main Tester Unit x1
Remote Unit x1
PoE Tester x1
BNC Adapter Cables x2
BNC Male/Male Adapter x1
RJ45 to RJ11 Adapters x3
Network Cable x1
User Manual x1
bSafety Instructions
Put the device always on astable and straight surface. It will damage the device if it falls.
Don't place the device into direct sunlight or in places with high temperature. This will damage the
device or shorten its average lifespan.
Don't place it near heat sources like radiators or other heat producing devices.
Don't expose the device to water, moisture or high humidity.
Don't place it in the bathroom or the kitchen near asink. Avoid direct contact with water.
Don't try to open the device.
Prior to the first use of our product make abackup of your data.
In the case of improper use, we are not liable for any loss of data.
In any case, liability for loss of data is limited to the effort that is necessary to restore from existing
backup copies.
Congratulations on the Purchase of WZ0015P!
Please read the manual and safety Instructions before using the product for the first time. Otherwise
damage may result.
waste. Its components must be recycled or disposed apart from each other. Otherwise contaminative and hazardous
According to the European WEEE directive, electrical and electronic equipment must not be disposed with consumers
Ksubstances can pollute our environment.
You as aconsumer are committed by law to dispose electrical and electronic devices to the producer, the dealer, or
BEN bic collecting points at the end of the devices lifetime for free. Particulars are regulated in national right. The symbol
on the product, in the user's manual, or at the packaging alludes to these terms. With this kind of waste separation,
application, and waste disposal of used devices you achieve an important share to environmental protection
CThe CE mark confirmed that this product meets the main requirements of the Directive 2014/30/EU of the European
Parliament and the Council of Europe concerning telecommunications and terminals regarding the Safety and health of
users and of electro-magnetic interference compliance. The CE has been demonstrated. These statementsare deposited
by the manufacturer.
AIntroduction
RJ45 jack
RJ45 jack
LED display for sourcing end (jack 1)
LED display for receiving end (jack 2)
Power switch
LED scanning mode switch
Test switch for manual scan
RJ45 jack
9. LED display for receiving end (same as jack 2)
10. Ground LED for receiving end
11. Battery compartment (9V)
12.RJ45 jack
13. Type A
14. Type B
SAND
Bin
dsSS&s8sg
a£on
Emernet position ma BIATIASS88 BATIA-S684 Ineas 14%
ME OEE ee Haa
AOperation
mLoopback Test
10Base-T Cable Test
1. Plug one end of tested cable on sourcing of RJ45 jack and another end of tested
cable on remaining receiving RJ 45 jack.
2. Slide power switch on, the upper row LEDs will start to scan in sequence if the Auto/Manual switch is
set on Auto mode, or the LED will light on pin 1if the Auto/Manual switch is set on Manual mode.
Note: You have to make sure the battery power is sufficient. If battery fails to the power, the LEDs
will be dimmed or hold up or no light, and the test result will be incorrect.
3. Choose the Auto/Manual switch to be Auto scan mode or Manual scan mode by pressing the Auto/
Manual switch.
4. In this moment the corresponding LED indicators of another row of LED will light up simutaneously.
5. Read out the result of LED display. It tells you the pin configuration status of the tested cable.
If you fail to read the result in the first run of LED scan, you may read it again in the second run of
LED scan, or use the manual mode and press the test switch one by one until you read the result out.
Loopback Test
Modular Cable test
Please follow up the procedures of 10Base-T Cable Test. However, the LED display should be
read as the right picture. RJ11/
RJ12
123456
0000000000
0000000000
12345678G
RJ45
10Base-2 Cable Test
1. Plug the two attached BNC adaptor cables on both RJ45 jacks, then connect the tested cable both
ends on BNC adaptor cables.
2. As to the remaining procedures, you may refer to 10Base-T cable test from step 1.2. to 1.5.
Note:
1) The center pin of BNC should be read on LED 1and shielding pin of BNC should be read
on LED 2. ceerognnE
BNC CENTER PIN T
2) As the 10Base-2 cable has only two wires, we suggest you to read the result of LED scan
by manual mode.
BNC SHIELDING
aRemote Test
1. Plug one end of tested cable on the sourcing RJ45 jack of master unit and another end on the
receiving RJ45 jack of remote unit. If the tested cable has already installed on the patch panel or
wall plate, you may use the adaptor cable to solve the connector gender problem.
mn
Patch Panel or Wall Plate
2. Now, set the Auto/manual switch on Auto mode if you work test alone.
3. Read the test result from LED display on remote unit.
Note: The LED display on remote unit was in seg
ing to the sourcing
end of master unit.
uTest Result
ie EEG Pin 2d
tinuity: jü
‚ontinuity: nednnnood in
2
is continue:
OE0OC0000
2. Open: 123456786G Pin
2
is opened
0000000000
Dea0CII00
3. Short: baaeDoned Pin 2 and Pin 3 are shorted
OON0O0000
4. Miswire: 12345678G Pin 3and Pin 6 are miswired
OOODORDOÛ
aWarning
.This tester is not intended for use on powered circuits. Attaching this tester to apowered circuit can
result in damage to the tester orinjury to the user.
+lf you will not use the tester for along time, take off the battery from battery compartment.
mPoE Test
Connectthe RJ45 cable
me
Lenen] 1,2,3,6 (Power 4,5,7,8 (Power)
Type AVv
Type BVv

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Logilink WZ0015 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info