Bedienungsanleitung Lorus 7T62 (Seite 2 von 2) (Englisch)

593729

Zoom out

Zoom in

Vorherige Seite

1/2

Nächste Seite

■ STOPWATCH

■ LUMIBRITE WATCH

✼ If your watch is a LORUS LUMIBRITE watch,

it has following features.

LORUS LUMIBRITE watches absorb and store

light energy from natural and artificial light

sources and emit light in the dark. They are

made of environmentally friendly material,

and therefore, are harmless to human beings

and the environment.

• With a full charge, LORUS LUMIBRITE

watches glow in the dark hours longer than

conventional luminous watches of this type.

If exposed to a light of more than 500 lux

(i.e., the brightness of a typical office) for

approximately 10 minutes, or direct sunlight

for 2 minutes, they will glow for hours.

•Since LORUS LUMIBRITE watches emit the

light they store, the brightness will decrease

gradually over time. The length of time they

will glow may also differ slightly depending

on such factors as the brightness of and

distance from the light source used to

charge the watch.

■ BATTERY CHANGE

The miniature battery SEIKO SR927W, Maxell

SR927W or SONY SR927W or EVEREADY

399,which powers your watch should last

approximately 3 years. However, because it

is inserted at the factory, the actual life of the

battery once in your possession may be less

than 3 years.

Be sure to replace the battery to prevent any

possible malfunction as soon as it runs down.

To replace the battery we recommend taking

the watch to a local watch repair shop.

Notes:

1. If the stopwatch is used for more than 2

hours a day and/or the alarm rings for more

than 20 seconds a day, the battery life may

be less than the specified period.

2. After the battery is replaced with a new

one, set the time/calendar and alarm and

adjust the stopwatch hand position.

■ CARE OF YOUR LORUS WATCH

• BATTERY

CAUTION

Do not expose the old battery to fire

or recharge it. Keep it at a place

beyond the reach of children. If a

child swallows it, consult a doctor

immediately.

• WATER RESISTANT

* If your watch is 200 M/20 BAR, 100 M/10 BAR

or 50 M/5 BAR water resistant, it is so

indicated on the dial/case back.

• Do not operate the buttons when the

watch is wet.

• If the watch is exposed to salt water, rinse

it in fresh water and then wipe it thoroughly

dry.

NO NO NO

YES

YES NO NO

YES YES NO

Condition

of use

Accidental

contact

with water,

such as

splashes

and rain

Swimming

and taking

a shower

Skin

diving

Scuba

diving

Indication

on the dial/

case back

Indication

YES

WATER

RESISTANT

WATER

RESISTANT

(50M/5 BAR

)

WATER

RESISTANT

100M/10 BAR

or above

(

Caution:

Leather straps are not water resistant except

so indicated, even if the watch head is water

resistant.

• ALLERGIC REACTION

Because the case and band touch the skin

directly, it is important to clean them regularly.

If not, shirt sleeves may be stained and those

with delicate skin may develop a rash. Please

wear the watch with some play to avoid any

possible allergic reaction. If you develop a

rash on your wrist, stop wearing and consult a

physician.

• MAGNETISM

Your watch will not be affected by magnetism

generated by household electric appliances.

•SHOCKS AND VIBRATIONS

Your watch may be worn for normal sports

activities, but be careful not to drop it or hit it

on hard surfaces.

• TEMPERATURE

Your watch is preadjusted so that constant

accuracy may be insured at normal tempera-

ture.

■ SERVICE

When your LORUS watch requires repair or

sevicing, please see the enclosed WARRANTY/

GUARANTEE.

Printed in China

✩ Before using the stopwatch, be sure to

check that the crown is set at the normal

position and that the stopwatch hands are

reset to the “0” position.

* If the hands do not return to the “0” position,

follow the procedure in “■ SETTING THE TIME

AND ADJUSTING THE STOPWATCH HAND

POSITION”.

Stopwatch operation

■ SINGLE-TIME ALARM

• The alarm can be set to ring only once at a

designated time within the coming 12

hours.

• The alarm time can be set in one minute

increments.

✩ Before using the alarm, check that the

alarm hands are adjusted to the current

time. (See “■ SETTING THE TIME AND

ADJUSTING THE STOPWATCH HAND

POSITION”)

1. Pull out the crown to the first click.

2. Press button “B” repeatedly to set the

desired alarm time.

* The hands move quickly if button “B” is kept

pressed.

3. Push the crown back in to the normal

position.

* The alarm is automatically engaged.

Notes:

1. The single-time alarm cannot be set for a

time more than 12 hours ahead of the

current time. While you keep button “B”

pressed to advance the alarm hands

quickly, they stop when they indicate the

current time. In that case, release button

“B”, and then, keep the button pressed

again to set the alarm hands to the desired

time.

2. While the crown is at the normal position,

the alarm hands indicate the current time

when the alarm is disengaged and the

designated alarm time when it is engaged.

• The stopwatch can measure up to 60

minutes in 1/5 second increments.

• After 60 minutes, it will start counting again

from “0” repeatedly up to 12 hours.

Start

Stop

Reset

Standard measurement

* Measurement and release of

split time can be repeated by

pressing button “B”.

Start Split

Split

release

Stop Reset

Split time measurement

Start

Finish time

of 1st

competitor

2nd

competitor

finishes

Finish time

of 2nd

competitor

Reset

Measurement of two competitors

● The alarm rings at the designated time for

20 seconds, and it is automatically

disengaged as it stops. To stop it manually,

press button “A” or “B”.

* While the stopwatch is measuring, the alarm

rings differently than usual. However, this is

not a malfunction.

* While the alarm is ringing, pressing button “A”

or “B” will only stop the alarm, and no

stopwatch operation can be made.

1. Pull out the crown to the first click, and press

and hold button “B” until the alarm hands

stop to indicate the current time.

2. Push the crown back in to the normal

position.

Note:

To correct the alarm time you have set, follow

the procedure described in “Alarm time

setting”.

To stop the alarm

To cancel the alarm time you have set

Alarm hour

hand

Alarm minute hand

Alarm time setting

* Restart and stop of the

stopwatch can be repeated

by pressing button “A”.

Start

Stop

Restart

Stop

Reset

Accumulated elapsed time measurement

Stopwatch 1/5-second

hand

A: Start /

Stop

B: Split /

Split release/

Reset

Stopwatch

minute hand

Lorus 7T62 Seite 2

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Lorus 7T62

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info