Bedienungsanleitung Lowrance X-15 (Seite 12 von 14) (Englisch)

599332

Zoom out

Zoom in

Vorherige Seite

1/14

Nächste Seite

marked when desired. To use the

marker,

simply press

the MARK

key

and a vertical line will be dis-

played

across the entire

page.

Hold the MARK

key

down and the

unit will

the vertical line for

long

as the

key

is held down.

Example:

Press: MARK

Result:

Figure

2L4

Scale

The numbers that indicate the

depth

or scale

may

be deleted if

desired.

Pressing

the SCALE

key

once will

stop

the

printing

of the

scale numbers. The scale

may

displayed again by pressing

the

SCALE

key.

Remember,

the scale

may

displayed

any

time

by pressing

either the LOWER LIMIT or the

UPPER LIMIT

key.

Example:

Press:

SCALE

End-of-Paper

Marker

The

graph paper

used

in the

X-15

has a

red

line

printed

at the

bottom of the

paper

signify

when there is

only

3 feet be-

fore the end of the

paper.

End of

PaperMark!5__

Figure

HOW TO READ GRAPHS

"Arched

Signatures"

A remarkable

advantage

of the

X-15

is that it can record individ-

ual fish with a characteristic

arched mark that

separates

them

from their

stationary surroundings.

The

reason for this is shown be-

low.

The distance to a fish when it

moves into the sonar's cone of

sound

is shown as "A' in

Figure

22.

When the fish has moved

the center of the

cone,

the dis-

tance to it will

shorter,

(line

"B"),

and as it moves out of the

cone,

the

distance will increase

again

as shown in line "C".

STYLUS

REPLACEMENT

CAUTION

—

High voltage

present

in the electronic section

when the unit is turned

on.

1. TURN THE UNIT

OFF.

Release both catches on the

top

the case. Pull out and

down

on the

top

of the case

front to

expose

the

stylus

belt.

(See

Figure 36.)

3. The

stylus

belt rides

over two

wheels located at the

right

edge

of the

platen assembly.

Move the front of the belt

DOWN to

position

the

stylus

at the center of the

platen.

4. Hold the

stylus

belt

stationary

with one

finger,

and remove

the old

stylus by starting

at its

left

edge

and

moving

it out

from under the tabs on the

stylus

holder.

5. Before

installing

the new

stylus,

be sure it is bent

prop-

erly by comparing

it to

Figure

37.

6. Refer to

Figure

38to be sure

the new

stylus

positioned

correctly

under the tabs on

the holder. Be sure it moves

freely

in the two slots. If

not,

bend the

stylus away

from the

edge

it is

rubbing

on until it

does move

freely.

7. After

installing,

the

stylus

won't

all the

way

down

the

paper,

(See Figure 39)

bend the

right leg

down so

that more

pressure

is exerted

against

the

stainless steel

plate.

If it

still does not

all the

way,

bend

the left

leg

down more

(but

not so far that

digs

into the

paper).

8. Close the front of the case.

Latch both catches on

the

top

of the case.

Figure

Result:

Figure

- Figure

PDF compression, OCR, web-optimization with CVISION's PdfCompressor

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Lowrance X-15 Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info