Bedienungsanleitung Lowrance X-15A (Seite 7 von 12) (Englisch)

599334

Zoom out

Zoom in

Vorherige Seite

1/12

Nächste Seite

wheels

by reversing

the

proce-

dure used to

remove the old

one. BE SURE

the

fingers

the new

stylus

are

pointed

UP.

6. Close the front of

the case.

Latch both

catches at the

top

of the unit.

MAINTENANCE

NOTE: The

stylus may

damaged

if it is in front of the

pla-

ten when the

platen assembly

pulled

down.

Always

move the

stylus

to the

back side of the

pla-

ten

when

changing

the

paper

rolls.

Remember to move the belt

down to remove the

stylus.

Black carbon dust is created dur-

ing

the

recording process.

Use a

soft,

oil-free

rag

to clean the

viewing

door and metal

platen

be-

hind the

paper.

Low

pressure

compressed

air

may

be used to

blow

dust out of the case and

away

from

moving parts

if the air

dry

and free of oil.

All mechanical

connections

should be

checked

periodically

be sure

they

haven't worked

loose.

HIGH VOLTAGE is

present

in the

transmitter section when the

unit

is ON.

attempt

should

made

by any

unauthorized

per-

son to

modify

repair

the

elec-

tronic

section.

All electrical

connections

should

be checked

periodically

and

cleaned as

necessary.

The

face of the

transducer,

mounted

on the transom

should

washed

periodically

with mild

soapy

water to remove

any

ac-

cumulated rod

grime

oily

film.

This is

essential to have

good

contact between

the transducer

and the water.

SECTION

carry

spare

fuse,

stylus belt,

and roll

paper.

Do use

the

empty

cardboard core

from the last

roll of

paper

on the

take-up post.

keep

the recorded

graphs

for

future

reference.

Do clean

the

stylus belt, wheels,

and

the rubber roller after

every

five rolls

ofpaper.

DON'T

SECTION

DONT OPEN THE

CASE WHEN

THE UNIT IS

ON.

Don't

pull

the

platen

assembly

down when the

stylus

is at the

front.

Don't store

any objects

inside the

case or behind the

viewing

win-

dow.

(Except

for small

pieces

tape.)

Don't

forget

tape

the

paper

the

take-up

core.

Don't rotate the

stylus

belt

up.

Don't use

oily cloths,

strong

sol-

vents,

or abrasive cleansers.

TROUBLESHOOTING

SECTION

Symptom

On/Off switch is

'ON",

but the

stylus

and

paper

don't move.

What To Do

Check

fuse;

check connections at

battery

for

tightness

and

corrosion.

Symptom

On/Off

switch is

"ON",

have

zero

mark,

but no echoes or bottom

signal.

What To

sure the transducer is

plugged

—

GRAYL NI

rrIviv

Han

'nan

a n--• a.

Figure

When

high Sensitivity settings

are

used,

a second bottom echo

will

appear.

This is normal

and is

caused

the

returning

signal

re-

flecting

off the surface of

the

water,

making

a second

trip

the

bottom and back.

If detailed information about

brush

piles,

individual

fish,

or the

thermocline is

desired,

the

Sen-

sitivity

knob

should be rotated to

approximately

the ¾

point.

Refer

to the

illustration below to see

Figure

SENSITIVITY:

TOO LOW

what effect the

Sensitivity

control

setting

has on

the recorded

information.

Recording

individual fish

with an

"arched"

signature

can

usually

accomplished

trolling speed

with the

Sensitivity

knob at the ¾

point,

higher.

Refer to the sec-

tion "Arched

Signatures"

for more

information about

this

important

function of

your

recorder.

Suppression

Control

The

Suppression

Control is

used to reduce

interference from

noise.

Noise,

electronic

terms,

any

undesired

signal.

It can

caused

an electrical

source,

(such

as the

engine's

ignition sys-

tem)

air bubbles

in disturbed

water which is call

cavitation. In

both

cases,

the noise

could

pro-

duce unwanted marks on

the

paper. (See Figures

7 &

8.)

Fortunately,

noise

pulses

are rela-

tively

short in time

compared

real sonar

signals. Advancing

the

Suppression

knob will cause

the

system

reject

these

unwanted,

short

pulses

without

reducing

the

Figure

SENSITIVITY: PROPER SETTiNG

PDF compression, OCR, web-optimization with CVISION's PdfCompressor

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Lowrance X-15A Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info