Bedienungsanleitung Lowrance X-16 (Seite 14 von 16) (Englisch)

599336

Zoom out

Zoom in

Vorherige Seite

1/16

Nächste Seite

place

near the

top

of the chart

paper.

A zero

adjust

control has

been

placed

on the back

inside

wall of the X-1 6 near the

upper

left hand corner so that the zero

line

position may

adjusted

the

paper.

Open

the case front and look for

the decal marked "ZERO

ADJUST". You

may

have to

pull

the

paper transport assembly

down to see the decal for the first

time. Push the

transport

closed

and turn on the unit.

(CAUTION

—

Keep

hands

away

from the

stylus

belt and

stylus. High

volt-

age

present.)

Insert a 6-8'

long

screwdriver

with a l/g" blade into the zero

adjust

hole and rotate the control

until the zero line is at the desired

position. (Note:

this

may

also be

adjusted

with the unit

turned

OFF.)

Adjust

the

control,

then remove

the screwdriver and turn

power

back ON.

Repeat

until the zero

line is in the desired

position.

IV HOW TO READ GRAPHS

'rched

Signatures"

A remarkable

advantage

of the

X-16 is that it can record individual

fish with a characteristic arched

mark that

separates

them from

their

stationary surroundings.

The

reason for

this is shown on

page

10.

(The

distance to a fish when it

moves into

the sonar's cone of

sound is shown as "A"

Figure

22).

When the

fish has moved to

the center of the

cone,

the dis-

tance to it will be

shorter,

(line

"B"),

and as it

moves out of the

cone,

the distance will

increase

again

as shown in

line "C".

8. Close

the front of the case.

Latch both catches

on the

top

of the case.

STYLUS BELT REPLACEMENT

CAUTION

—

High voltage

present

in the electronic section

when the unit is turned on.

TURN THE UNIT OFF.

Release both catches on

the

top

of the case. Pull out and

down

on the

top

of the case

front and the

platen

expose

the

stylus

belt.

3. The

stylus

belt rides over two

pulleys

located at

the

right edge

of the

transport

assembly.

Move

the front of the

belt DOWN to

position

the

stylus

at the center

of the

platen.

Grasp

the belt at the

stylus

holder with the

thumb and fore-

finger

and move it

gently

to the

left while

pushing

the belt off

the

pulleys

with the other

finger.

(See Figure 37.)

5. Position the new belt on

the

pulleys by reversing

the

pro-

cedure used to remove

the old

one. BE SURE the

fingers

the new

stylus

are

pointed

UP.

6. Close the front of the

case.

Latch both catches

at the

top

the unit.

MAINTENANCE

Remember,

the

stylus may

damaged

if it is in front of the

platen

when the

transport

assem-

bly

pulled

down.

Always

move

the

stylus

to'the back side of the

transport

assembly

when

chang-

ing

the

paper.

The

stylus

belt

should be rotated

down to remove

the

stylus.

Never rotate

the

stylus

belt

up.

Black carbon

dust is created

during

the

recording process.

Use

soft,

oil-free

rag

clean the

viewing

door and

transport

assem-

bly.

Low

pressure compressed

air

may

be used to blow dust out

the case and

away

from

moving

parts

the air is

dry

and

free of oil.

After

every

five rolls of

paper,

the

stylus

belt and

pulleys

it rides

on should be

wiped

clean

with

soft

rag

moistened with

alcohol to

remove carbon dust.

All mechanical connections

should be checked

periodically

be sure

they

haven't worked loose.

not

apply any type

of lubri-

cant to the motors or

gear

trains.

High voltage

present

in the

transmitter section when the unit

is on.

attempt

should be made

by any

unauthorized

person

modify

repair

the electronic

section.

corrosion should occur at the

power plug,

fuse

holder,

power

cord

splices,

battery

connec-

tions,

clean as

required

and check

to make sure that

good

contact is

being

made at all

terminations.

The face of the

transducer,

exposed

to the

water,

should be

FIGURE 22

partial

arch occurs most of

the time

your unit,

(the

mark

curves

up,

but

not back

down,

vice-versa)

it is because the trans-

ducer is not

pointed straight

down.

your

transducer is mounted on

the

transom,

adjust

the transducer

until the fish show the

distinctive

arched

signature.

This

may

take

some trial and error until the

correct

mounting

achieved.

FIGURE 21

:4rwt:rr:

,-,t

-7' _i'"-

____

,— fl.8

r——r

U E1-—

D2rt-z----- LUWRSS

FIGURE 23

FIGURE 37

12 17

PDF compression, OCR, web-optimization with CVISION's PdfCompressor

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Lowrance X-16 Seite 14

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info