Bedienungsanleitung Luvion Exact non-contact (Seite 4 von 20) (Englisch, Holländisch, Französisch)

775744

Zoom out

Zoom in

Vorherige Seite

1/20

Nächste Seite

6 7

• Don’t use the non-contact thermometer in high humidity environments.

• Patients should not drink, eat, or be physically active before/while taking the

measurement.

• Before placing the thermometer sensor onto the measurement area, remove

hair, sweat, or dirt.

• Use an alcohol swab to carefully clean the sensor and wait for 5 minutes before

taking a measurement on another patient.

• 7 short beeps will sound when the temperature is higher than 37.5 °C in order

to alert the patient that he/she may have a fever.

• Always take the temperature in the same location, since the temperature read-

ings may vary from dierent locations.

• In the following situations it is recommended that three temperatures in the

same location be taken and the highest one taken as

the reading:

1) Newborn infants in the rst 100 days.

2) Children under three years of age with a compromised immune system and for

whom the presence or absence of fever is critical.

3) When you’re using the thermometer for the rst time until you have familiar-

ized yourself with the instrument and obtain consistent readings.

6. Explanation of displays and operation instructions

LCD display Operation instructions and explana-

tion of displays

Sound and backlit

1. Measurement of body

temperature

1. Aim the temperature sensor (1)

at the measurer’s forehead directly

(eective distance 1 to 6 cm), under

shutdown state press button (2)

or hold down button (2), the LCD

display will display the measured

forehead temperature.

Body

temperature mode

1. When temperature

value is between

32.0°C and 37.6°C

there will be one long

beep and green backlit

for 3 seconds.

2. When temperature

value is

Holding down the button and scan-

ning over the forehead is suggested.

The system will read sequentially

and show the maximum value.

2. Measurement of milk tempera-

ture. Under shutdown state Press

button (3) and release it within 4

seconds. the LCD display will display

the measured milk temperature.

3. Press button (2) or (3) under

startup mode to measure again.

Attention:

There will be 7 short rapid beeps

when the measured temperature

exceed 37.5°C/99.5°F which is a

warning for patients that he/she

might have a fever.

between 37.6°C/99.6°F

and 42.2°C/107.9°F,

there will be 7 short

beeps and red backlit

for 3 seconds.

Milk temperature

mode

1. When the tempera-

ture value is between

0.0°C/32.0°F and

100.0°C/212.0°F there

will be a long beep

and green backlit for 3

seconds.

The feeding bottle symbol will be

visible in the left top corner when

in Milk temperature mode. The °C

symbol will blink when the reading

is ready.

The forehead symbol will be visible

in the right top corner when in Body

temperature mode. The °C symbol

will blink when the reading is ready.

1. The measured value exceeds

100°C/212.0°F under milk tempera-

ture mode.

2. The measured value exceeds

42.2°C/107.9°F under body

temperature mode.

3 short beeps and red

backlit for 3 seconds.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Luvion Exact non-contact Seite 4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info