541009
106
Zoom out
Zoom in
Vorherige Seite
1/118
Nächste Seite
10.4 Rear Seat Device (LX8000D or LX8080D)
In two-seat gliders it is possible to install the LX8000D rear seat device. The LX8000D looks
almost identical to the LX8000. However inside the device there is no GPS or Flarm module.
The rear seat device must be connected only to the LX8000 via the RS485 bus system.
Power is available from the bus hence no external power is needed. The device can be
switched on only when the LX8000 is powered on.
The basic idea of two-seat configuration is that both devices work independently from each
other with the possibility to exchange various data on user request or automatically.
10.4.1 Data Exchange
Because the GPS and Flarm modules are not integrated in the LX8000D this data is received
from the LX8000 digital unit through RS485 bus.
After power on, the LX8000 also sends polar data and pilot information to have them
synchronised in both devices.
The user can define which data will be automatically synchronised between the LX8000 and
LX8000D.
Way point and task databases are not synchronised between the LX8000 and
LX8000D. To have databases synchronised you have to use the SD card and copy
files from the rear to front device or vice versa. See Chapter 5.1.5.4 for how to
copy way point files.
To set up data which is going to be received from the LX8000D, enter the “Rear seat device”
menu on LX8000 digital unit (see Chapter 5.1.12.5).
To define which data is going to be received from the LX8000 go to “Front seat device”
menu in the LX8000D unit (see Chapter 5.1.12.5).
Data is divided into two groups; flight parameters and navigational data. If a specific value
is checked this value will be automatically be received from the other device.
Check MacCready, Ballast and/or Bugs to receive the current MacCready value, current
ballast setting or bugs from the other device.
If Waypoint is checked a new way point target will be automatically assigned when the
user changes the way point target on the other device. A message
“Waypoint target
received”
will be shown on the screen and you will be navigating to the same way point as
106

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für LX NAV LX8080 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Andere Handbücher von LX NAV LX8080

LX NAV LX8080 Bedienungsanleitung - Deutsch - 158 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info