Bedienungsanleitung Lynx Aurora 16 (Seite 9 von 32) (Englisch)

586985

Zoom out

Zoom in

Vorherige Seite

1/32

Nächste Seite

Page 7

inputs and outputs and the TRIM/AES MODE button still displays and controls the TRIM value.

However, if the unit is in “DUAL WIRE SELECT” Mode, AND the METER button is on DIGITAL,

then the TRIM/AES MODE button controls the AES MODE. Details are in the section below.

a TRIM/AES MODE

When the meter select switch is set to analog, this button allows the nominal trim level to be set for the

analog inputs and outputs to either +4dBu or -10dBV. When selected from the front panel button, this

setting impacts all channels of input and output together, however analog inputs and outputs can be

altered in groups of four channels when the Aurora is remotely controlled. Remote control operation is

indicated when both LEDs are on. Note: the Trim button is disabled on the Aurora 16-VT.

When the METER select is set to digital, and the Aurora is in “DUAL WIRE SELECT” Mode, then

this control allows configuration of the AES/EBU digital I/O. When not in “DUAL WIRE SELECT”

Mode, then setting the METER button to “DIGITAL” will still reveal the TRIM mode, not the Dual

Wire state. To Enable “DUAL WIRE SELECT” Mode, the TRIM/AES MODE button needs to be

pressed in while AC Power is applied. In this state the dual wire state can be selected with the METER

button set to “DIGITAL”. To exit DUAL WIRE MODE, power-cycle the Aurora. Four modes of

operation are possible:

Both LEDs OFF Single Wire I/O Mode. Allows all channels of digital input or output to

operate at sample rates up to 192kHz.

DUAL WIRE IN ON Dual Wire Input Mode. Allows compatibility with legacy dual wire input

devices. In this mode, the number of available input channels is reduced by

½ (Aurora 16 = 8, Aurora 8 = 4).

DUAL WIRE OUT ON Dual Wire Output Mode. Allows compatibility with legacy dual wire

output devices. In this mode, the number of available output channels is

reduced by ½ (Aurora 16 = 8, Aurora 8 = 4).

Both LEDs ON Dual Wire I/O Mode. Enables dual wire mode for both inputs and outputs,

allowing 8 channels maximum of digital I/O for the Aurora 16, and 4

channels for the Aurora 8.

s POWER

This button controls the standby state of the Aurora. When the front panel LEDs are not lit, the Aurora

is in standby mode. In this state the Aurora is not functional and is using a minimal amount of power.

To completely power down the Aurora, it must be unplugged from the AC power source.

When the Aurora is in standby mode, pressing the POWER button will illuminate the front panel

LEDs indicating that the Aurora is now ready for use. When the Aurora is in on mode, pressing the

POWER button for ½ second will put the unit into standby mode.

Holding the POWER button while connecting AC power to the Aurora will toggle the power-up mode

to either ON or STANDBY. PLEASE NOTE: After the mode is changed the unit must be put into

standby mode to save this setting before power is removed. See Section 2.2 for more information.

PLEASE NOTE: It is best to wait until SynchroLock has achieved lock before using the Aurora for

recording. See

e above).

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Lynx Aurora 16 Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info