Bedienungsanleitung Lynx Aurora 8 (Seite 8 von 32) (Englisch)

586986

Zoom out

Zoom in

Vorherige Seite

1/32

Nächste Seite

Page 6

No LED SynchroLock is disabled by remote control or the source is outside of SynchroLock range

and the Aurora has reverted back to the wide-range analog PLL. If SynchroLock failed

to lock, you can tap through the SYNC SOURCE options to return to the original source

to re-engage the SynchroLock clocking system.

r TO ANALOG OUT

This button selects the signal source that will be routed to the analog outputs. This is a global

selection, affecting all analog channels. Channels are mapped to directly corresponding channels (i.e.

In 1 to Out 1, In 2 to Out 2, etc.). Individual channels may be routed to specific output destinations

when the external control is used. Choices are:

ANALOG IN Signals from Analog In 1-16

Aurora 8 Signals from Analog In 1-8

AES IN Signals from Port A and Port B Digital In

Aurora 8 Signals from Port A Digital In

LSLOT IN Signals from LSLOT expansion device inputs (for instance ADAT lightpipe)

All 3 LEDs ON In this mode, front panel routing has been bypassed, and routing will be managed by

external control.

t TO DIGITAL OUT

This button selects the signal source that will be routed to the digital outputs. As with the TO

ANALOG OUT selection, this setting impacts all digital channels, whereas per channel routing is

possible with external control. It is possible to route digital inputs to digital outputs, allowing the

Aurora to function as a standalone digital router. Channels are mapped to directly corresponding

channels (i.e. In 1 to Out 1, In 2 to Out 2, etc.). Signal Choices are:

ANALOG IN Signals from Analog In 1-16

Aurora 8 Signals from Analog In 1-8

AES IN Signals from Port A and Port B Digital In

Aurora 8 Signals from Port A Digital In

LSLOT IN Signals from LSLOT expansion device inputs (for instance ADAT lightpipe)

All 3 LEDs ON In this mode, front panel routing has been bypassed, and routing will be managed by

external control.

y IR/MIDI

This LED illuminates to indicate activity from the MIDI input or IR transceiver. This could indicate

that the external control software is being used or that the firmware is being programmed via IR or

MIDI.

u PEAK METERS

These meters display the instantaneous peak level of audio being sent to the Aurora analog or digital

inputs. The intensity of the lower row of orange LEDs indicates signal strength. The upper row of red

LEDs indicate overload.

i IR Transceiver

The infrared transceiver mounted on the front panel of the Aurora provided the ability to control

parameters and view level meters and settings via handheld, laptop or desktop PC with Infrared

capabilities. However, this functionality is no longer supported with current firmware updaters and the

Aurora Remote Control software.

o METER

This button determines whether the peak meters display input activity for the digital or analog inputs.

This button also determines the behavior of the TRIM/AES MODE controls. When the ANALOG

LED is ON the meters indicate the levels for the analog inputs and outputs and the TRIM/AES MODE

button controls the TRIM. When the DIGITAL LED is ON the meters indicate the levels for the digital

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Lynx Aurora 8 Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info