Bedienungsanleitung Lynx Aurora LT-TB (Seite 41 von 55) (Englisch)

587002

Zoom out

Zoom in

Vorherige Seite

1/55

Nächste Seite

One may need to change the ID because a unit has changed position, been added, or for some

reason the existing order is not appropriate to the context of use.

We generally want to assign unit order in a way that is consistent with the physical ordering

of units. For instance, if you have 4 Auroras in a rack, you might want to make the bottom

unit number 1, the next unit up in the rack #2, etc. Device order is set from the Lynx Mixer.

1. If the driver is not already installed, follow the procedure in Section 5.3: Installing

Aurora Driver to install the Lynx Driver. Reboot when prompted

2. Launch the Lynx Mixer (Windows: All Programs > Lynx Studio Technology. OS X:

Applications)

3. Click Settings > Advanced > Adapter Settings. The Auroras should show up with their

numerical identifier. For instance “3:Aurora 16” means that unit has hardware ID 3.

4. When you click the Interface Name in the list, all of the LEDs on the front panel of that

Aurora will illuminate. In this way you can determine which Aurora in the list

corresponds to an Aurora in the rack.

5. Use the “Move Up” or “Move Down” buttons to change the order to what is desired. For

instance, if you wish for the unit that appears as #3 to be #1, use the Move Up button two

times. It should now appear as “1: Aurora 16”.

6. You can also set the unit’s desired Channel Mode at this time (see Section 5.5: Channel

Mode). If one wishes to use only the analog I/O, then 16-channel mode would be the

appropriate choice. For Analog AND AES Digital I/O, then 24 or 32-channel mode

would be the correct option.

7. After selection, click “Save”, then close the Lynx Mixer.

8. Turn each Aurora OFF with the front panel switch, then turn it back ON again. This will

save its state.

9. To verify settings, clicking on each unit in the “Adapter Settings” page will function as

an “Identify”, and cause the associated unit’s LEDs to flash.

8.1.3 Set the SYNC SOURCE

Now that the units are cabled up, boot the computer. Once the OS has loaded, launch the

Lynx Mixer to set the SYNC SOURCE for each interface. Select each unit from the tabs on

the left part of the Lynx Mixer screen, and then click the SYNC SOURCE dropdown menu

in the Navigation Bar to choose the desired source. For the units that are word clock slaves,

the correct selection would be EXT.

Verify that SYNC SOURCE on the front panel reflects the chosen setting.

After setting each Aurora to its desired configuration, turn the unit OFF and the ON from the

front panel power switch. This will save the unit’s state.

8.1.4 Configure for use

In Windows, one can use the Sound section of Control Panel to select whichever unit is

desired as the default playback device. Unfortunately, Windows is known to jumble the

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Lynx Aurora LT-TB Seite 41

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info