Bedienungsanleitung Lynx Aurora LT-TB (Seite 44 von 55) (Englisch)

587002

Zoom out

Zoom in

Vorherige Seite

1/55

Nächste Seite

assumed that the application uses the Windows default audio device. To use the desired

Aurora output as the system default:

With Windows 7 /Windows 8 navigate to:

Start > Control Panel > Sound > Playback. Right-Click the desired Lynx Aurora TB output

device and choose “Set as default device”. Note: With Multiple Auroras, the device IDs can

be misrepresented here. See Section 8.14: Configure for use.

Even when 24 or 32-channel mode is selected for the Aurora, 8 stereo WDM play and record

devices will appear to the operating system (all 24 or 32 channels will show when ASIO is

used). Play devices are labeled as Aurora Speakers (this is equivalent to Play 1+2), Aurora

Play 3+4, Aurora Record 1+2, Aurora Record 3+4, etc. These are pre-configured to connect

to appropriate hardware I/O on the Aurora by default, although this can be user altered in the

Lynx Mixer Play Panel. So for instance, Play 1+2 streams to Analog Outpus 1+2, Record

1+2 receives signals from analog inputs 1+2, etc.

As an example, if you wish to have a multimedia/WDM application stream to Aurora Analog

Output 7+8, you would choose Aurora 7+8 as the play device. If the software did not allow

device selection and only used the Windows default play device, then you would set the

Windows Default in the Sound Section of Control Panel to Aurora 7+8.

It is possible for WDM applications to stream to the digital outputs instead of analog on an

Aurora 16. The settings involved would be relative to the channel mode you were in. If you

are in 16-channel mode, then all signals will be sent simultaneously to the Analog and Digital

Outputs. For instance, if audio is sent to Play 3+4, audio would stream to Analog Out 3+4

AND Digital Out 3+4 at the same time. If you are in 24 or 32 channel mode, you would need

to assign Play Devices 1-16 to the Aurora Digital Outputs. You do this in the Lynx Mixer,

with the Play and Output panes. See Section 7: Lynx Mixer Reference for details.

An Aurora 8 displays a maximum of 16 channels, so its analog and digital outputs will be

available automatically.

8.3.1.2 WDM Multi-Channel Playback and Recording

The Aurora-TB is capable of playing back and recording multi-channel interleaved audio,

such as 5.1 surround sound. The driver supports playback of up to 16 channel audio through

a single Play device.

For playback, several conditions must be met for successful multi-channel playback.

1. The only driver device that supports multi-channel interleaved operation is

“Speakers”. If your playback software allows you to select the play device

specifically, choose “Aurora Speakers”. If it does NOT allow you to choose the

output device, and uses the system default instead, then set the default play device

in the Sound section of control panel to “Aurora Speakers”

2. In the Sound Section of Control Panel, select “Speakers” and then click the

“Configure” button. Set the AUDIO CHANNELS selection to your desired

playback format: 5.1, 7.1, quad, etc.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Lynx Aurora LT-TB Seite 44

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info