Bedienungsanleitung Lynx Aurora LT-TB (Seite 50 von 55) (Englisch)

587002

Zoom out

Zoom in

Vorherige Seite

1/55

Nächste Seite

9 Troubleshooting

There is an error message during the driver installation:

1. Verify that the LT-TB has been installed correctly and there is an LED flashing on the

LT-TB board when unplugged. The LED should go solid when a Thunderbolt cable is

connected. See Section 5.3: Installing the Lynx Driver.

2. Verify that the TB cable is connected correctly and that the computer TB ports are active

and the drivers are functional.

3. Verify that your Aurora has firmware revision 28 or above

The LT-TB does not show up in the Operating System as a usable device:

1. Check that the LT-TB is correctly installed and verify that the green LED (D30) on the

LT-TB is flashing.

2. Close the Lynx Mixer and any audio applications and reset the LT-TB either by removing

then reinserting the TB cable, or by turning the Aurora off for 5 seconds, then turning it

back on.

3. Verify that the Aurora has firmware revision 28 or above. To determine what firmware

revision your Aurora has, press the TRIM and POWER buttons at the same time with the

power to the Aurora off. If the LED flashes over the numbers 2 on the input row & 8 on

the output row or above (i.e. 2&9, 3&0, etc.) in the Aurora Meter Display, then your unit

is compatible with the LT-TB. If pressing Power and Trim does not cause any LEDs to

flash, causes a sequence lower than 28 to flash, or causes a single number to flash, then

your unit needs to be updated.

4. Check that the OS is compatible with the LT-TB. One must be running OS X 10.8.5+ or

Windows 7 or 8 (32-bit or 64-bit).

The Aurora shows up in the Operating System as a usable device, but will not pass

audio:

1. Make sure that the LT-TB has been assigned as the active device in the application being

tested. Many audio applications allow a specific audio device to be selected from a

configuration menu. Other applications will use whatever the operating system default

device is. In this case verify that the Aurora has been configured as the default playback

device for the system.

2. Check that the source for TO ANALOG OUT is set to “LSLOT IN”.

3. Check the Lynx Mixer Outputs Panel and see if there is meter activity for the appropriate

outputs being used. If there is, check the cable connections from the Aurora analog or

digital outputs to the monitoring equipment.

4. Click “Restore Defaults” in the Lynx Mixer.

5. Close the Lynx Mixer and any audio applications and reset the LT-TB either by removing

then reinserting the thunderbolt cable, or by turning the Aurora off for 5 seconds, then

turning it back on.

6. Verify that the Aurora has firmware revision 28 or above. To determine what firmware

revision your Aurora has, press the TRIM and POWER buttons at the same time with the

power to the Aurora off. If the LED flashes over the numbers 2 on the input row & 8 on

the output row or above (i.e. 2&9, 3&0, etc.) in the Aurora Meter Display, then your unit

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Lynx Aurora LT-TB Seite 50

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info