Bedienungsanleitung Lynx Hilo TB (Seite 56 von 68) (Englisch)

586999

Zoom out

Zoom in

Vorherige Seite

1/68

Nächste Seite

Page 52

6 Appendices

6.1 Battery Information

Hilo can operate off of a portable DC Battery Pack for field recording or whenever AC power is not available. The

BATTERY IN connector is located directly above the AC connector on the Hilo back panel.

Battery Packs can be purchased from retailers of video cameras and other electronics equipment. Almost any lead acid

or lithium battery should work as long as it has the following characteristics:

• 9-18 Volts. Typical choices are either 12V or 14V.

• A 4-pin XLR connector. The connection should have pin 4 hot, and pin 1 for ground. No other pins are

connected. This is a standard configuration.

• Hilo consumes 22 Watts. Check with the battery’s stated watt hours to determine operating time you can

expect with a fully charged battery. For instance, a 60 watt-hour battery would provide up to 2.72 hours of

operation.

6.2 Setting Trim Pots

As discussed in sections 3.4.5 and 3.4.6, Hilo’s Line Inputs and Line Outputs can be set to Trim values of +18 dBu;

+20 dBu; +22 dBu; +24 dBu; +0 dBV; +2 dBV; +4 dBV and +6 dBV. These trim positions are factory calibrated to

these values within 1/100th of a dB. Trim levels can be selected from the Hilo Home Page. These set levels will satisfy

the overwhelming majority of Hilo users.

In some cases, these levels may need to be tweaked to match the reference level of gear that is not calibrated as

accurately. Also, in time and due to changes in temperature, it may be necessary to tweak trim levels to set them back

to their original reference.

For this purpose, Hilo has ultra accurate, 25-turn trim pots accessible from the bottom of the chassis that can be used to

adjust + or - .5dB from the established trim level. Here are the steps to calibrate via these trim pots:

1. Remove the plate from the bottom of Hilo. There are four screws that

hold it in place. The front-right rubber foot will need to be removed to

allow access to one of the screws. Locate the input and output trim

pots on the underside of the Hilo main board.

2. Set the Line In and/or Line Out trim levels on the Hilo Home page to

the value closest to your desired level.

3. It is best to use sine wave tones to adjust trims. If adjusting Input trim levels, send tones from an external

device and measure the results in either software or a scope with digital inputs. It is best to avoid analog input

routed to analog output paths for this kind of calibration. If adjusting Hilo Output Trims, send tones from a

software source via the USB connection, or tones from an external device connected to one of Hilo’s digital

inputs routed to the Line Out. Make sure that the entire signal path is set to unity gain.

4. Adjust the trims clockwise to increase the gain on the inputs or outputs, or counter clockwise to decrease gain

until the desired reference level is achieved.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Lynx Hilo TB Seite 56

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info