Bedienungsanleitung Lynx L22 (Seite 23 von 36) (Englisch)

586988

Zoom out

Zoom in

Vorherige Seite

1/36

Nächste Seite

Page 23

Troubleshooting

Audio playback sounds fast or slow when I am using the digital input as

the clock source.

When the digital input is selected as the clock source, the Lynx L22’s sample clock will

run at the sample rate of the incoming digital input signal. In the case when the sample

rate of this signal is 48 kHz and a file being played was actually recorded at 44.1 kHz,

the audio will playback fast. To solve this problem either change the sample rate of the

device driving the digital input or select Internal as the sample clock source using the

Lynx L22 mixer.

How do I minimize record monitor latency when I am doing overdubs?

Use the Lynx L22’s on-board monitor circuitry. This is controlled by the Lynx L22

mixer.

What does the green LED on the Lynx L22 indicate?

When lit, the LED indicates successful initialization of the Lynx L22 and the driver.

When I connect the Lynx L22 analog outputs to the MIC inputs on my

Mackie mixer I hear distortion.

The MIC inputs are being overdriven. Even with the mic gain adjusted to its lowest

setting, the maximum signal level that the MIC inputs of the smaller Mackie mixers

can handle is +14 dBu. In the +4 dBu trim setting, the Lynx L22 is capable of delivering

a +20 dBu signal. To solve this problem use 1/4” line inputs of the mixer. This requires

the use of XLR to TRS adapters as described in the “External Connections” section.

I connect my microphone directly to the Lynx L22 Analog Input

connectors, but the level is very low, what is going on?

The Lynx L22 Analog Input connectors should be connected line level devices only.

To record from a microphone, first route the signal through a microphone pre-amplifier

or mixer and then into the Lynx L22.

Where on the Lynx L22 do I connect my internal CD-ROM drive?

The Lynx L22 has no connector for an internal CD-ROM drive. We recommend using

digital audio extraction software to capture the audio data from your CD’s and saving

it to your hard disk drive as .WAV files. Using this method, the audio files can be

played back using the D/A converters on the Lynx L22 which have far superior

performance to those found in most CD-ROM drives. If your CD-ROM/DVD drive

can reliably extract digital audio then you could use Windows Media Player (Version 7

or higher) to extract digital audio from CDs and play it in real-time with no physical

connection between the Lynx L22 and the CD-ROM drive.

Can I leave my current sound card in my computer while using the Lynx

L22?

You may leave your existing sound card in your computer as long as you have a free

PCI slot and interrupt for the Lynx L22. You may need to reconfigure certain software

to access the Lynx L22 instead of your existing sound card. Please refer to the “Working

with Third Party Applications” section for details.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Lynx L22 Seite 23

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info