Bedienungsanleitung M-Audio Hammer 88 (Seite 11 von 52) (Deutsch, Englisch, Französisch, Italienisch, Spanisch)

707307

Zoom out

Zoom in

Vorherige Seite

1/52

Nächste Seite

Program Change Increment/Decrement

Using the Hammer 88 editor application, it is possible to configure the Pedal inputs or –/+ buttons to send

an Increment (increase) or Decrement (decrease) Program Change message each time it is pressed. When

one pedal is configured to increment through sound Programs (such as, 1, 2, 3, etc.), and another to

decrement through them (such as, 127, 126, 125, etc.), the second pedal will not decrement from where the

first pedal left off (for example, 2, 1, 0). This is in contrast to the buttons. The + button will only increment

and the – button will only decrement. Pressing + to increment to the value of 127 and then pressing the –

button will decrement the value to 126. Furthermore, pressing the – sends values such as 127, 126, 125,

etc, and will decrement from where the + button left off (for example, 125, 126, 127). When set to Program

Inc/Dec, each of the buttons will light up white briefly when pressed.

MMC

The – and + buttons can be assigned to send a MMC (MIDI Machine Control) message. MMC is a transport

control protocol that is used to remotely control some recording hardware and DAWs. When set to MMC,

the – button will send a Stop message and the + button will send a Play message. The – and + buttons will

be lit red while stopped and green while playing.

Editing Controls Using the Editor Application

For full details on editing controls, see the separate Hammer 88 Preset Editor User Guide on m-audio.com.

Troubleshooting

General

Here are answers to common questions you may have when using your Hammer 88 keyboard:

Problem 1: My M-Audio hardware suddenly stopped working after having performed fine since

installation.

Solution 1: Switch off the unit and let it sit for 10 seconds. Then restart your computer and try again.

Problem 2: I have plugged a sustain pedal into my M-Audio keyboard, but it works opposite as to

what I'm expecting.

Solution 2: The polarity of the sustain pedal is calculated by the keyboard when it is powered on. When

Hammer 88 is powered on, the sustain pedal is assumed to be in the OFF position. If you want the sustain

pedal to be off when it is not depressed, make sure the pedal is not depressed when you power on Hammer

88.

Problem 3: When I press a key, there is a delay before I hear any sound.

Solution 3: This delay is known as latency. Latency with MIDI signals is due to the software application you

are using. MIDI data is simply control data. The MIDI data is read by your software. The software then

completes a large number of complex calculations in order to produce the sound you hear—all this takes

time.

We strongly recommend a proper audio interface. Refer to m-audio.com for a selection of options. If you

already have an adequate audio interface, try reinstalling the latest drivers for the audio interface, or try

reducing the buffer sizes of the audio drivers.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

M-Audio Hammer 88 Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info