Bedienungsanleitung M-Audio Oxygen 25 (Seite 11 von 88) (Deutsch, Englisch, Französisch, Italienisch, Spanisch)

707324

Zoom out

Zoom in

Vorherige Seite

1/88

Nächste Seite

Setting Toggle Values (Min/Max) for Buttons or the Sustain Pedal

It is possible to set a Toggle Value for a button or the sustain pedal, causing it to send one value when first pressed

and another value when pressed again. This means that one value is sent the first time it is pressed, and another

value is sent the next time it is pressed.

When configuring a button or the sustain pedal to operate in Toggle Mode, the following four values need to be

specified:

Key

Parameter

Value

Control Assign

Toggle On/Off operation

146

Data 1 (example)

MIDI CC number

10 (Pan)

Data 2 (example)

Second press

0 (minimum)

Data 3 (example)

First press

127 (maximum)

NOTE: When working with proprietary M-Audio parameters from the 128-255 range, the "Control Assign" setting is

used to configure a button or the sustain pedal for this special mode of operation. This means that certain values

that are usually specified through the "Control Assign" setting must instead be specified via the "Data 1" parameter

(such as the standard MIDI CC parameter in the example below).

The following example will configure a button to "hard pan" the sound to the right speaker when it is pressed for the

first time, and "hard pan" to the left speaker when it is pressed for a second time. This involves configuring the

button to operate as a toggle, while controlling the Pan parameter (MIDI CC 10):

1. Press the Edit button.

2. Press the Select button or Control Select (Ctrl Sel) key.

3. Select a button as described earlier in this guide.

4. Press the Control Assign (Ctrl Asgn) key.

5. Type 146 using the number keys. This configures the button to operate as a toggle.

6. Press the Data 1 key.

7. Type 10 using the number keys. This specifies which parameter the button will toggle “on and off”. In this

example, MIDI CC 10 (Pan).

8. Press the Data 2 key.

9. Type 0 using the number keys. This sets the second button press value to zero. In other words, sound will be

panned "hard left" when the button is pressed a second time.

10. Press the Data 3 key.

11. Type 127 using the number keys. This sets the first button press value to the maximum value, so that the sound

is panned “hard right” when the button is pressed the first time.

12. Press the Enter key.

TIP: It can be useful to transmit two other specific values instead of sending minimum (zero) and maximum (127)

values as in the above example. When assigning a button to control Pan (MIDI CC 10), you can, for example,

configure Data 2 to send Value 38, and Data 3 to send Value 93, effectively causing pan to switch between the

approximate "ten o’clock" and "two o’clock" positions when pressing the button the first time, and pressing the

button the second time.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

M-Audio Oxygen 25 Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info