Bedienungsanleitung M-System MSG-90 (Seite 4 von 28) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Portugiesisch, Spanisch)

522907

Zoom out

Zoom in

Vorherige Seite

1/28

Nächste Seite

CONTROLS of Fig. 21:

A) Reduces the luminous intensity to minimum. When the key is pressed for 2" the lights go off.

B) Switches on the lights calling the last level of luminous intensity set. Increases the luminous intensity to maximum.

C) Reduces the motor speed until reaching minimum. If pressed for 2", the motor is switched off.

If pressed for 2" when the Filter Alarm is active, the HOUR counter is reset.

D) Drives the motor (calling the last speed used) and increases the speed until reaching maximum.

E) Activates/deactivates the sensor (AUTOMATIC or MANUAL mode). In Automatic mode the sensor is active and

the letter “A” appears on the display (L).

L) Display:

- signals the running speed.

- signals Automatic mode by displaying the letter “A”. When the motor speed is changed, the running speed is

displayed flashing times, and then the letter “A” reappears.

- signals the filter alarm (with motor off) by displaying the central segment for 30".

FILTER ALARM: Displayed for 30" when the motor is off:

After 30h of operation, the letter “F” appears on the display; It indicates that the grease filters need to be cleaned.

After 120h of operation, the letter “F” flashes on the display; It indicates that the grease filters need to be cleaned and

the charcoal filters replaced.

After cleaning the grease filters (and/or replacing the charcoal filters), restart the hour counter (RESET) by pressing

the key C during display of the filter alarm.

GAS SENSOR SENSITIVITY: The sensitivity of the sensor can be modified to suit your requirements. To modify the

sensitivity, the appliance must be in manual mode (i.e. the running speed and not the letter “A” must appear on the

display); If not, press the key E.

Modify the sensitivity by simultaneously pressing the keys D and E. The set sensitivity is indicated on the display.

By means of the buttons C(-) and D(+) the desired sensitivity is set Store the “new” sensitivity by pressing the key

ATTENTION: TO PREVENT DAMAGING THE SENSOR, DO NOT USE SILICONE PRODUCTS NEAR THE HOOD!

Grease filters: special attention must be given to the grease filters which must be periodically cleaned, whenever

the grease filter alarm trips. For instructions of the filter Alarm, refer to the Controls paragraph. Remove the filters

as shown in para. 1 and wash with neutral detergent.

Charcoal filters: if the filtering version appliance is used, the charcoal filters will have to be periodically replaced

when the charcoal filter alarm trips. For instructions on the filter Alarm, refer to the Controls paragraph. Removing

the charcoal filter/s: take away the metallic grille (Fig.3a) and the grease filter (Fig.3b/3c). Remove the coal filter pushing

the lock inside, rotate the filter until taking away the two small tongues from their sides (Fig.17).

Lighting: to reach the lamps you remove the metallic support tightening the two screws (Fig.22) and moving it oo

the right ; to replace the halogen lamps tighten the locknut in the anti-clockwise direction and pull out the bulb (Fig.23).

Replace the lamps of the same type.

This appliance is marked according to the European directive 2002/96/EC on Waste Electrical and Electronic

Equipment (WEEE). By ensuring this product is disposed of correctly, you will help prevent potential negative

consequences for the environment and human health, which could otherwise be caused by inappropriate waste handling

of this product. The symbol on the product indicates that this product may not be treated as household waste. Instead

it shall be handed over to the applicable collection point for the recycling of electrical and electronic equipment. Disposal

must be carried out in accordance with local environmental regulations for waste disposal. For more detailed information

about treatment, recovery and recycling of this product, please contact your local city office, your household waste

disposal service or the shop where you purchased the product.

DEUTSCH

BESCHREIBUNG

Die Haube steht in Umluftversion und in Abluftversion zur Verfügung.

Umluftversion (Abb.1): Die Haube saugt die mit Rauch und Gerüchen gesättigte Luft an und reinigt sie durch die

Fett- und die Kohlefilter. Danach wird die saubere Luft wieder in den Raum geleitet. Um die gleichmäßige Wirksamkeit der

Kohlefilter zu erhalten, müssen sie regelmäßig ausgetauscht werden. Die Kohlefilter werden nicht mitgeliefert.

Abluftversion (Abb.2): Die Haube saugt die mit Rauch und Gerüchen gesättigte Luft an, leitet sie durch die Fettfilter

und gibt sie über ein Abführungsrohr nach außen ab. Diese Version benötigt keinen Kohlefilter.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

M-System MSG-90 Seite 4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info