Bedienungsanleitung M-System MSPK951IX (Seite 18 von 32) (Deutsch, Englisch, Holländisch, Französisch, Italienisch)

680055

Zoom out

Zoom in

Vorherige Seite

1/32

Nächste Seite

the quantity of smoke and odours being produced under the hood. When

the function is active, BL6 becomes active.Each time that the motor

changes speed, either automatically or forced by the user, BL6 lighting

blinking for a few seconds.

30h filter ALARM: After 30 hours of operation, an alarm switches on to

signal the need for anti-grease filter cleaning.The filter alarm, when active,

is displayed for 30 sec each time the motor is deactivated:BL6 remains

ON.During this period, it is possible to reset the alarm by pressing the TC6

button for longer than a second.

120h filter ALARM: After 120 hours of operation, an alarm switches on to

signal the need for active carbon filter (optional) replacement.The filter

alarm, when active, is displayed for 30 sec each time the motor is

deactivated:BL6 lighting blinking.During this period, it is possible to reset the

alarm by pressing the TC6 button for longer than a second.

Buttons TC5 + TC6 (ASC sensitivity): ASC odour sensor sensitivity can be

varied on 4 different levels as needed by pressing buttons TC5 and TCS

simultaneously for more than 1 second.The motor must be OFF and

automatic function NOT active.When sensitivity setting function is

activated:all BL switch OFF (no display) then BL6 activates FIX.After 1

second, the BL2-BL5 LEDs will show the set sensitivity value, BL2 for lower

sensitivity up to BL5 which indicates higher sensitivity. You can set a

different value using corresponding keys TC2, TC3, TC4 or TC5. To save

the new sensitivity, press TC6 or wait until the function deactivates

automatically.

It can be varied on your keyboard (for cleaning) with a long press of the

buttons TC1 and TC6 simultaneously. When the cleaning mode is active,

the keys TC1 and TC6 remain lit. To exit cleaning is necessary to activate

the buttons again TC1 and TC6 pressed simultaneously (long), or wait for 5

minutes.

Work Time Limit: if the hood is left on (lights and/or motor), after 10 hours

in the absence of commands from the user, it will automatically switch to

OFF condition with all services switched off.

Buzzer: the Buzzer emits a "beep" each time that a command is set from

the keyboard or remote control (optional).

Controls of Fig. 49

Key A: light switch;- position 0: light off;- position 1: light on.

Key B: motor switch; - position 0: motor off; - position 1-2-3: motor first,

second and thrid speed motor on.

MAINTENANCE

! Before cleaning or maintenance cut the power.

Cleaning the hood

WHEN TO CLEAN IT: clean it at least every 2 months to prevent the risk

of fire.

EXTERNAL CLEANING: use a cloth moistened in lukewarm water and

neutral detergent (for painted hoods); use specific products for steel,

copper or brass hoods.

INTERNAL CLEANING: use a cloth (or brush) soaked in denatured ethyl

alcohol.

WHAT NOT TO DO: do not use abrasive or corrosive products (e.g. metal

sponges, brushes, too hard brushes, very aggressive detergents, etc.)

Cleaning the grease filters

WHEN TO CLEAN IT: clean it at least every 2 months to prevent the risk

of fire, in according to use.

HOW TO REMOVE THE FILTERS: push the catch near the handle towards

the rear of the hood and pull the filter downwards

HOW TO CLEAN THE FILTERS: hand wash or in the dishwasher using a

neutral detergent. If washing in the dishwasher, possible discoloration of the

filters does not in any way compromise their functioning.

Replacing the charcoal filter

(for filtering version only)

WHEN TO REPLACE IT: replace it at least every 6 months, in according to

use.

HOW TO REMOVE IT: If using the hood in the filtering version, the

charcoal filter will have to be replaced. To switch off, pull the latch inward

and rotate the filter downwards.

Lighting

- Replace with light bulbs of the same type.

- If the light spot is damaged, it must be replaced only by the

manufacturer, its service agent or similarly qualified persons in order to

avoid a hazard.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

M-System MSPK951IX Seite 18

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info