Bedienungsanleitung M-System MU-50 (Seite 3 von 24) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Portugiesisch, Spanisch)

522902

Zoom out

Zoom in

Vorherige Seite

1/24

Nächste Seite

filters both when the central segment goes on and when it starts blinking. The filter alarm can be seen when the

motor is off and for about 30 seconds. To reset the hour counter, keep the button pressed for 2 seconds while

the alarm can be seen.

Controls shown in Fig. 16:

AUTOMATIC OPERATION WITH SENSOR:

Key A : switches the lights on/off. Key B : enables/disables “Automatic” function. When this function is selected,

an “A” appears on the display C, and the speed of the motor increases or decreases depending on the smoke,

odours and gas present in the kitchen. Display C : - indicates the automatic operation of the sensor (the

letter “A” appears);- indicates the motor speed selected automatically by the sensor; indicates the filter alarm

whenever the central segment is illuminated or flashing. Key D : decreases motor speed / Reset; decreases

motor speed to zero (stopping); in any case however, after approximately 1 minute, the hood resumes automatic

operation at the speed set by the sensor. Whenever the key is pressed during the display of filter alarms,

a RESET occurs, and the counting of the hours resumes again. Key E : increases motor speed; in any case

however, after approximately 1 minute, the hood resumes automatic operation at the speed set by the sensor.

Modification of sensor sensitivity: sensor sensitivity can be modified by operating as follows:

- stop the hood by pressing key B. – Simultaneously press keys D and E (the sensor’s sensitivity index will

appear on the display) - Pressing keys D or E, the sensor’s sensitivity will either increase or decrease (1

: minimum sensitivity / 9: maximum sensitivity). – whenever the power supply is interrupted, the sensor will

resume operation with a sensitivity index of 5.

Warning: in order to avoid damaging the sensor, never use silicone products near the hood!

OPERATION AS TRADITIONAL HOOD:

Key A : switches the lights on/off. Display C : - indicates the motor speed selected (from 1 to 4); - indicates

the operation of the Timer when the number is flashing; - indicates filter alarms whenever the central segment

is illuminated or flashing. Key D : decreases motor speed / Stop / Reset; decreases motor speed to zero

(stopping). Whenever the key is pressing during filter alarm display, a RESET occurs, and the counting of the

hours resumes again. Key E : enables the motor / increases motor speed /TIMER. Pressing this key starts

the motor (at the latest speed set); pressing the key again increases motor speed, while keeping the key pressed

down for a few seconds enables the TIMER, and 5 minutes later the motor will stop (while the number of speed

setting selected will simultaneously begin flashing on the display); the Timer will remain enabled if motor speed

is changed. In order to disable the Timer, press the key again.

Controls shown in Fig. 17:

Switch A: LIGHT; position 0: light off; position 1: light on. Switch B: MOTOR

SPEED: makes it possible to select the motor operating speed; position 0: motor off. C: Motor on light.

Controls shown in Fig. 18:

Key A: turns the lights on/off; every 30 hours of operation the corresponding

pilot lamp (S) comes on to indicate that the grease filters must be cleaned; every 120 hours of operation the

corresponding pilot lamp (S) flashes to indicate that the grease filters must be cleaned and the charcoal filter

replaced. To restart the hour counter (RESET), hold the button A pressed down for about 1” (while the pilot lamp

S is on). Key B: drives the motor in first speed (the corresponding pilot lamp comes on); when holding it down

for about 1”, the motor cuts out; when pressing the button a second time (while the pilot lamp is on) , the TIMER

is activated and thus the motor stops after 5’ (the pilot lamp flashes). Key C: drives the motor in second speed

(the corresponding pilot lamp comes on); when pressing the button a second time (while the pilot lamp is on) ,

the TIMER is activated and thus the motor stops after 5’ (the pilot lamp flashes). Key D: drives the motor in

third speed (the corresponding pilot lamp comes on); when pressing the button a second time (while the pilot lamp

is on) , the TIMER is activated and thus the motor stops after 5’ (the pilot lamp flashes). Key E: drives the motor

in fourth speed (the corresponding pilot lamp comes on); when pressing the button a second time (while the pilot

lamp is on) , the TIMER is activated and thus the motor stops after 5’ (the pilot lamp flashes).

Pay special attention to the grease filters:

if the model purchased has the controls shown in Figure 15/16:

the grease filters must be cleaned approximately once every 30 hours of operation (when the central segment

on the display goes on or starts blinking). Once the cleaned filters are reinstalled, keep button R (Reset) pressed

for two seconds to reset the counter. If the model purchased has the controls shown in Figure 17: the grease

filter must be cleaned periodically: exactly how often depends on use (at least once every other month). Wash

out the filter using a neutral soap. If the model purchased has the controls shown in Figure 18: the grease filters

must be cleaned approximately once every 30 hours of operation (when the light button lamp comes on) - Fig.18S).

Wash out the filter using a neutral soap. Once the cleaned filters are reinstalled, to reset the counter hold the

light button pressed down for about 1” (Fig.18A) while the corresponding pilot lamp (S) is on. IMPORTANT: The

metal grease filters must be periodically cleaned following the above instructions, while the synthetic grease filters

(white colour) must be replaced, according to the same cleaning frequency as the metal filters.

Removing the grease filters:

- For the model shown in Fig. 6: remove the metal grid by moving the 2 side fasteners (A). Remove the filter

retainers (Fig. 19F) and then the metal (or synthetic) grease filter (Fig. 19G).

- For the models shown in Fig. 7 and 8: remove the metal grease filter by moving fastener B and turning the

filter outwards.

M-System MU-50 Seite 3

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info