Bedienungsanleitung M-System MVK-90 (Seite 3 von 16) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Spanisch)

522898

Zoom out

Zoom in

Vorherige Seite

1/16

Nächste Seite

that purifies the air sent back into the room.

In the Ducting version (Fig. 2), cooking vapours and odours

are conveyed straight outside by a disposal duct which

passes through the wall/ceiling. Use of charcoal filter is

therefore unnecessary.

According to the model you have bought, the appliance can

include 1 or 2 motors. In the I motor version the flange for

the air to be exhausted has not got a central position, but

it is slightly on the left.

INSTALLATION

-----------------------------------------------------------

Before assembling, in order to manoeuvre the appliance

more easily, take off the grease grille (Fig. 3): pull the front

of the grille upwards; desinsert the back from its seat.

IMPORTANT: So as not to damage your product, during

installation USE ONLY THE SCREWS PROVIDED. Make

sure these are used as shown in the following instructions.

To compensate possible depth voids between the appliance

and the wall, a plastic

SPACING BAR to be fixed at the

back of the appliance by means of the three screws A is

included (Fig.4). The 3 screws A to be used are contained

in the accessory bag attached to the plastic spacing bar.

Cut the spacing bar according to the distance to be

adjusted.

Assembly under a pensile cupboard

The following operations are essential for as-sembly:

– Install the wiring system

– Prepare the air venting hole if your appliance is to be

installed in the Ducting version.

Fixation as indicated in Fig. 5:

Using the relative template make the 4 necessary fixing

holes in the bottom of the cupboard and cut the air venting

hole.

Move the hood close to the bottom of the wall unit and then

connect the two units by means of the 4 self-tapping

screws supplied together with the appliance.

Fixation with brackets as in Fig. 6 (optional):

Take the two brackets (S) out of the accessory bag

together with the 8 screws provided. Fit the brackets to

the wall unit being careful to position these correctly; for

this operation use the 4 longer screws. At this point,

secure the appliance to the brackets using the 4 shorter

screws.

Ducting version: connect the flange of the hood with the air

venting hole made previously in the wall/ceiling by means

of an adequate tube. Make the electrical connection of the

hood by means of the power supply cable. Assemble the

grease grille with the hood, inserting it obliquely (making the

front side go upwards).

Filtering version: connect a proper pipe to the flange of the

hood so that the air is sent outside the pensile and sent back

into the room. Make the electrical connection of the hood

by means of the power supply cable. Set the charcoal filter

(Fig. 7A) inside the grease grille blocking it by means of the

2 supplied metal wires (F), as indicated in Fig. 7; the 2 metal

wires must be threaded into the relevant slots.

Assemble the grease grille with the hood, inserting it ob-

liquely (making the front side go upwards).

OPERATION

-----------------------------------------------------------

Controls (Fig. 8):

A = ON/OFF 1st speed switch

B = II speed switch

C = III speed switch

The motor is automatically ON or OFF by opening/

closing the truck (unless switch A is on 0). Opening

the truck the motor works according to last speed

registered.

D = Light switch:position A (automatic), the light are

automatically regulated ON or OFF by the opening/

closing of the truck. Position M (manual), the light is

on. Position 0, the light is off.

In case the hood is a filtering version one, it is necessary

to change the charcoal filter(s) according to utilization

about every six month. To remove the filter:

– open the truck pulling it first downwards, then towards

the front.

– take off the grease grille: pull the front of the grille

upwards; desinsert the back from its seat.

– take off the charcoal filter (A) from the inside of the

grease grille taking off the 2 metal wires F (Fig. 7) that

blocks it.

Light bulb

- If the fluorescent light or incandescent lamps need

changing, slacken the light cover by disconnecting the

screw and remove the bulb itself (Fig. 9). Replace with a bulb

of the same type.

- To change the rectangular halogen bulbs open the cover

and remove the bulb without touching it with bare hands

(Fig.10). Replace with a bulb of the same type.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

M-System MVK-90 Seite 3

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info