Bedienungsanleitung M-System MVW-600 (Seite 34 von 52) (Deutsch, Englisch)

522705

Zoom out

Zoom in

Vorherige Seite

1/52

Nächste Seite

Installing the machine

Positioning the machine

When determining the place to put your ma-

chine on, take care to choose a place where you

can easily load and unload your dishes.

Do not put your machine in any location where

there is the probability for the room tempera-

ture to fall below 0°C.

Before positioning, take the machine out of its

packaging by following the warnings located on

the package.

Position the machine close to a water tap or

drain. You need to site your machine, taking

into consideration that its connections will not

be altered once they are made.

Do not grip the machine by its door or panel in

order to move it.

Take care to leave a certain clearance from all

sides of the machine so that you can comforta-

bly move it back and forth during cleaning.

Make sure that the water inlet and outlet ho-

ses do not get squeezed while positioning the

machine.

Also, make sure that the machine does not

stand on the electrical cable.

Adjust the machine’s adjustable feet so that it

can stand level and balanced. Proper positio-

ning of the machine ensures problem-free ope-

ning and closing of its door.

If the door of your machine does not close pro-

perly, check if the machine is stable on the ﬂoor

it stands; if not, adjust the adjustable feet and

ensure its stable position.

Water connection

Be sure that the indoor plumbing is suitable for

installing a dishwasher. Also, we recommend

that you ﬁt a ﬁlter at the entrance of your place

or apartment so as to avoid any damage to

your machine because of any contamination

(sand, clay, rust etc.) that might be occasion-

ally carried in through the mains water supply

or the indoor plumbing, and to forestall such

complaints as yellowing and formation of depo-

sits after washing.

Water inlet hose

Do not use the water

inlet hose of your old

machine, if any. Use the

new water inlet hose

supplied with your ma-

chine instead. If you are

going to connect a new

or long-unused water in-

let hose to your machine,

run water through it for a while before making

the connection. Connect the water inlet hose

directly to the water inlet tap. The pressure

supplied by the tap should be at a minimumof

0.03 Mpa and and at a maximum of 1 Mpa. If

the water pressure is above 1 Mpa, a pressu-

re-relief valve should be ﬁtted in between.

After the connections are made, the tap should

be turned on fully and checked for water tight-

ness.

For the safety of your machine, make sure to

always turn off the water inlet tap after each

wash programme is ﬁnished.

NOTE: Aquastop water spout is used in some

models. In case of using Aquastop, a dange-

rous tension exists. Do not cut Aquastop water

spout. Do not let it get folded or twisted.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

M-System MVW-600 Seite 34

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von M-System MVW-600

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info