782325
15
Zoom out
Zoom in
Vorherige Seite
1/60
Nächste Seite
Technical and legal
information
MSTS1500-A by MacAllister
b) Never leave the table saw unattended when in operation. Turn if off and
don't leave the tool until it has come to a complete stop. An unattended
running saw is an uncontrolled hazard.
c) Locate the table saw in a well lit and level area where you can maintain
good footing and balance. It should be installed in an area that provides
enough room to easily handle the size of the workpieces. Cluttered, dark
areas, and uneven slippery floors invite accidents.
d) Regularly clean and remove wood shavings and saw dust from under
the saw table and/or the dust extraction unit. Accumulated saw dust is
combustible and may self ignite.
e) Secure the table saw. A table saw that is not properly secured may move or
tip over.
f) Remove tools, wood scraps etc. from the table saw before turning it on.
Distraction or possible jams can be dangerous.
g) Always use blades of the right size and with the appropriate mounting
hole (e.g. starshaped or round). Blades that do not match the mounting
hardware of the saw will run off-centre, causing loss of control.
h) Only use 10" saw blade with kerf width>2.3mm and blade body thickness is
1.8 mm match the riving knife with thickness of 2 mm.
i) Always use only a saw blade diameter in accordance with the markings
on the saw; Use only saw blades for which the maximum possible speed
is not less than the maximum spindle speed of the product.
j) Never use damaged or incorrect saw blade mounting means such as
flanges, saw blade washers, bolts or nuts. These mounting means were
specially designed for your saw, for safe operation and optimum performance.
Do not use any blunt , cracked, deformed or damaged saw blades. Only
replace the saw blade with one complying with the European standard
EN 847-1.
k)Never stand on the table saw, do not use it as a stepping stool. Serious
injury could occur if the tool is tipped or if the cutting tool is accidentally
contacted.
l) Make sure that the saw blade is installed to rotate in the proper direction.
Do not use grinding discs or wire brushes on a circular table saw.
Improper saw blade installation or use of accessories not recommended may
cause serious injury.
5. Additional safety instructions
- These operating instructions are intended for people with basic technical knowledge
regarding the operation of a machine like this or similar electrical power tools.
Inexperiencend persons are strongly advised to seek competent advise and
guidance from an experienced person before operating this machine.
Getting started...
15
EN
15

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Mac Allister MSTS1500-A wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info