Bedienungsanleitung Macrom 42 29 (Seite 7 von 26) (Deutsch, Englisch, Französisch, Italienisch, Spanisch)

166337

Zoom out

Zoom in

Vorherige Seite

1/26

Nächste Seite

CONTROLS AND INDICATORS

1 • RCAINPUT CONNECTORS: connect the pre-output leads of the head

unit to the input connectors.

2 • INPUT MODE SELECTOR: allows to select the amplifier’s

configuration as follows:

a) STEREO “ST” when the amplifier is used as a two-channel stereo

system (right + left);

b) MONO (L mono) when the amplifier is driven by one input signal “Left”

and outputs are mono-bridged.

NOTE: in this configuration, no signal is present at the “Right” pre-output

RCAoutput connection;

c) MIX “L+R”: when the amplifier is designed to drive one or more subwoofers according to the

1-, 2- or 3-channel configurations. Thus, the inputs signals will be blended into one signal.

NOTE: anyway, the signals present at the Pre-output outputs will always be stereo.

3 • INPUT GAIN ADJUSTMENT CONTROL: input sensitivity ranges from 200 mV to 2V.

Set the mid position for all MACROM units.

In case the amplifier is to be connected to a head unit that is not of MACROM make but is

fitted with preamplified RCAoutputs, proceed as follows:

a) set the volume control of your head unit to 3/4 of maximum ouput

level;

b) set the input gain control to the point where the maximum sound

level with no distortion is obtained.

4 • LOW-PASS SELECTOR SWITCH: it allows to select the

amplifier’s output mode by activating the Low-Pass crossover.

a) Flat: the amplifier reproduces the whole range of frequencies from 20 Hz

to 20kHz

b) Low: the amplifier reproduces low frequencies only.

5 • LOW-PASS FREQUENCY ADJUSTMENT: allows the continuous

adjustment of the low-pass frequency between 30 and 600 Hz, to

determine the end point of the audio range present at the amplifier’s

outputs and at the Pre-output outputs should the low-pass filter be selected.

6 • HI-PASS FREQUENCYADJUSTMENT: allows the continuous adjustment of the high-pass

frequency between 30 and 600 Hz, to determine the starting

value of the audio range present at the Pre-Output outputs.

7 • PRE-OUTPUT SELECTOR SWITCH: allows to select the

Pre-output output mode as follows:

a) FLAT: a signal having the same form and amplitude as the

input signal is present at the Pre-output outputs;

b) LOW: a low-pass signal is present at the Pre-output outputs

in order to drive an additional amplifier. Frequencies can be

adjusted by means of the LOW-PASS FREQUENCY “5”

control;

c) HIGH: a high-pass signal is present at the Pre-output outputs in order to drive an additional

amplifier. Frequencies can be adjusted by means of the HIGH-PASS FREQUENCY “6” control.

600Hz30Hz

150Hz

33Hz

36Hz

45Hz

70Hz

100Hz 250Hz

340Hz

470Hz

520Hz

580Hz

Flat Low

20Hz 20kHz

20Hz 30>600Hz

L(mono) ST L+R

20Hz 20kHz

20Hz 30>600Hz

Flat Low High

30>600Hz 20kHz

O/M 42.29 26/06/02 10:19 Page 7

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Macrom 42 29 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info