Bedienungsanleitung Magnani MI-HA-CFM01 (Seite 6 von 38) (Deutsch, Englisch, Holländisch, Französisch)

770357

Zoom out

Zoom in

Vorherige Seite

1/38

Nächste Seite

First use:

• Remove the device and accessories from the box. Remove any stickers, protective lm or plastic from the

device.

• Make sure the plug is removed from the power socket.

• Before you use the device for the first time, wipe all the removable parts with a damp cloth. Never use

aggressive or abrasive cleaning materials, a scouring sponge or steel wool; these damages the device.

• Clean the water tank F before rst use. Remove the detachable water tank F and lift the tank cover E. Fill

the water tank F with clean fresh water. Remove the water from the water tank F by turning the water tank

over F. Repeat these steps ± 3 times.

• Do not use any washing up liquids in the water tank!

• Fill the water tank F with clean fresh water and do not exceed the “MAX” water level, dry the water tank

exterior F with a dry cloth.

• Place the tank properly back on the device.

• Place the device on a at, stable surface, in a place where it cannot fall over.

• Make sure the steam control knob D is in the “O” position!

• Connect the device to the mains power.

• Press the power button C, the LED indicator next to the power button will illuminate RED. The LED indicator

next to the coffee brewing start/stop button A will slowly ash green.

• Select the single or double mesh L and insert it correctly into the metal funnel M. Make sure the tube on

the funnel aligns with the groove of the mesh. Do not put any coffee in the mesh. Then insert the funnel into

the device from the “Insert” position and secure the funnel by turning it counterclockwise until it is at the “Lock”

position.

• Once the coffee brewing start/stop LED indicator stops ashing, press the coffee brewing start/stop button A

and the hot water will be owing out. First a small volume will ow, after ± 3 seconds there will be a continuous

ow. During operation the LED indicator will ash.

• Press the coffee brewing start/stop button A again to stop the ow. Now the water is lled in the pump of the

device and the pipes are cleaned.

• The device is now ready for use.

Filling the water tank

• Remove the detachable water tank F

• Open the tank by lifting the tank cover E

• Fill the water tank with clean fresh water.

• Make sure the water tank is lled at least above the “MIN” mark and not above the “MAX” mark on the water

tank.

• Close the water tank cover and place the tank properly back into the device.

Pre-heating

To make a cup of good hot Espresso coffee, we recommend preheating the device before making coffee,

including the funnel, lter and cup, so the coffee avor cannot be affected by the cold parts.

• Make sure the water tank is lled at least above the “MIN” mark and not above the “MAX” mark.

• Select the single or double cup mesh L and put it correctly into the metal funnel M.

• Make sure the tube on the funnel aligns with the groove of the mesh. Do not put any coffee in the mesh.

• Insert the funnel into the device from the “Insert” position and secure the funnel by turning it counterclockwise

until it is at the “Lock” position.

• Place a cup on the removable shelf K and make sure it aligns with the funnel.

• Make sure the steam control knob D is in the “O” position!

• Press the power button C, the LED indicator next to the power button will illuminate RED. The LED indicator

next to the coffee brewing start/stop button A will slowly ash green.

• Once the coffee brewing start/stop LED indicator stops ashing, press the coffee brewing start/stop button A

and the hot water will be owing out. First a small volume will ow, after ± 3 seconds there will be a continuous

ow. During operation the LED indicator will ash.

• Press the coffee brewing start/stop button A again to stop the ow.

• Keep the hot water in the cup, so the cup stays warm.

• Caution: Prevent burns. Do not touch the hot parts and water; these are very hot.

Making espresso

• First pre-heat the cup as described in “Pre-heating”.

• Remove the funnel O by turning it clockwise to the “Insert” position.

EN 04

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Magnani MI-HA-CFM01 Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Magnani MI-HA-CFM01

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info