Bedienungsanleitung Magnat Anniversary 4000 STARK (Seite 8 von 52) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Portugiesisch, Spanisch, Schwedisch)

581732

Zoom out

Zoom in

Vorherige Seite

1/52

Nächste Seite

Dear MAGNAT Customer,

The ANNIVERSARY 4000 STARK car hifi power amplifier will enable you to satisfy your high demands on sound reproduction in your car.

With its impressive deep-bass power reserves, low harmonic content and neutral reproduction, the ANNIVERSARY 4000 STARK takes car

hi-fi to new heights. The amplifier is characterized by low operating current, rapid switching capabilities and excellent temperature stability.

Increased output power can be achieved by switching two amplifier channels in an amplifier together in bridging mode. Experience and

enjoy how this high-tech machine perfectly reproduces magnificent sound.

Please read all of the owner’s manual before installing and using the amplifier.

1. TECHNICAL DATA

Stereo / Bridged

Max. output power (1 kHz sinus burst 2:8, B+=14.4V) 4 x 400 W / 2 x 1200 W on 4 Ohm

Nominal output power (DIN 45 324, B+=14.4V) 4 x 150 W / 2 x 480 W on 4 Ohm

Max. output power (1 kHz sinus burst 2:8, B+=14.4V) 4 x 600 W on 2 Ohm

Nominal output power (DIN 45 324, B+=14.4V) 4 x 240 W on 2 Ohm

Loudspeaker impedance (stereo mode) 2 – 8 Ohm

Frequency response 5 – 75 000 Hz (-3 dB)

Total harmonic content (DIN 45 403) < 0.025% (1 kHz)

Stereo separation (IEC 581 ) > 65 dB (1 kHz)

Weighted noise distance (IEC A) > 100 dB

Input sensitivity LOW LEVEL INPUT 0.2 – 6 V

Input impedance LOW LEVEL INPUT 20 kOhm

Low-pass filter 30 – 150 Hz, 12 dB per octave

High-pass filter 10 – 300 Hz, 12 dB per octave

Bass boost 0 – 12 dB at 45 Hz

Supply +12 V (10 – 15 V), minus to ground

Fuse 100 A Maxifuse

Sizes (W x H x D) 504 x 55 x 230 mm

Weight 5.6 kg

SUBJECT TO TECHNICAL CHANGE

2. FEATURES

· Complementary push-pull final stage

· Stable at 2 ohms

· Infinitely adjustable high-pass filter

· Infinitely adjustable low-pass filter

· Infinitely variable bass equalisation

· Bridgeable 4-/3-/2-channel mode

· Electronic protective circuit against short circuiting, DC offset and excess temperature

· Mute switch for suppressing switch-on crackle interference

· Capsulated and gilded loudspeaker and power-supply screw terminals

· Status indicator (green LED) and overload indicator (red LED)

· Remote control for regulating the volume of the rear channels (CH3 / CH4) (subwoofer operation)

3. IMPORTANT INSTALLATION INFORMATION

· This appliance may only be connected to a 12 volt system with negative ground.

· The heat radiated when the amplifier is used means that sufficient air circulation is required at the place of installation. It is very

important that the cooler’s cooler ribs do not contact any metal plating or any surfaces which could impair air circulation. The amplifier

may not be installed in small confined spaces or spaces without air circulation (e.g. spare wheel recess or under the vehicle carpeting).

Installation in the boot is recommended.

· Install the amplifier in such a way that it is protected as far as possible against vibrations and dust and dirt.

· Make sure that the input/output cables are sufficiently distant from the power supply cables as otherwise interference may occur.

· Make sure that the fuse and operating elements are accessible after installation.

· The appliance’s reliability and performance depend on the quality of installation. Preferably get an expert to install the system,

particularly if you want to install several loudspeakers or a complex multi-way system.

4. CONNECTIONS

4.1 POWER SUPPLY AND AUTOMATIC SWITCHING ON

Important notice: Before commencing the installation, disconnect the plus terminals from the car battery in order to prevent

short circuits.

The power cabling usually installed in on-board car networks is not sufficient for a power amplifier’s demands. Make sure that the power

lines to GND and to the +12 V terminal have been sufficiently specified. A cable cross-section of at least 25 mm² must be used to connect

the battery to the amplifier’s terminals.

First connect the amplifier’s GND terminal to the battery’s minus pole. It is very important that the connection is good. Dirt residues must

be carefully removed from the battery’s connection point. A loose connection may cause malfunctions or interference noise or distortion.

The +12 V amplifier connection must then be connected with a power cable possessing an integrated fuse to the battery’s plus pole. The

fuse must be located close to the battery, the length of cable from the battery’s positive pole to the fuse must be less than 60 centimetres

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Magnat Anniversary 4000 STARK Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info