Bedienungsanleitung Magnat INTERIOR ICQ 262 (Seite 7 von 44) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Portugiesisch, Spanisch, Schwedisch)

581716

Zoom out

Zoom in

Vorherige Seite

1/44

Nächste Seite

Dear MAGNAT Customer,

Congratulations on your fine new loudspeakers and thank you very much for choosing MAGNAT! You

have made an excellent choice. The high-quality speakers produced by MAGNAT are renowned all over

the world.

Please study the instructions and information below carefully before using your new loudspeakers.

MAGNAT INTERIOR ICQ/IWQ LOUDSPEAKERS - SPECIALLY DESIGNED FOR CEILING FITTING/

WALL MOUNTING

Magnat Interior ICQ/IWQ speakers have an ingenious clamping mechanism that enables you to easily fit

them into a hole cut into a baffle. The easiest way is to fit them in a plaster board or similar ceiling. When

using an opening in a masonry wall, a plaster or timber board is also needed. For the fitting dimensions,

please see the technical data given at the end of the manual.

Removing the grille (fig. 1)

The clamping mechanism for attaching the speaker can be accessed after removing the protective grille.

Loosen the screws and move the clamps to position A. After placing the appliance in the cut-out hole,

tighten the screws. This automatically turns the clamps to position B and tightens them. See fig. 2.

GENERAL INFORMATION ABOUT CONNECTING YOUR MAGNAT LOUDSPEAKERS

Please always use a good quality loudspeaker connection cable from an audio dealer. To prevent

impairment of sound quality, we recommend cables with cross-sections of at least 1 mm² for lengths up

to 3 m and at least 1.5 mm² for lengths above 3 m.

Always turn off the amplifier or receiver before connecting or disconnecting loudspeaker cables. Place

the loudspeakers in their planned positions and cut the cables to the right length. The cables for both

channels should always be exactly the same length.

Strip 10 – 15 mm of insulation from the ends of the cables and twist the ends. The loudspeaker terminals

are equipped with a clamping mechanism (fig. 3). Press the terminal head down and guide the stripped

cable end into the hole on the side. On releasing the terminal head, the cable is secured, ensuring the

best possible contact.

For good sound it is imperative that the cables must be connected in such a way that the speakers are

“in phase”. This means that the black negative terminals on the speakers (-) must be connected to the

negative (-) terminals on the amplifier, the red positive (+) speaker terminals to the positive (+) amplifier

terminals. To make this easier one wire of most speaker cables is marked with a coloured strip or a ridge

in the insulation.

Before switching on the system double-check all your connections and make sure that the terminal screws

are tight and that there are no short circuits caused by stray wire filaments – this could cause serious

damage to your amplifier!

ACOUSTIC ADAPTATION

The crossover facilitates individual sound adjustment of the speaker system via high-quality jumpers:

1. Tweeter level adjustment (treble) (fig. 4A)

2. Mid-range adjustment (woofer) (fig. 4B)

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Magnat INTERIOR ICQ 262 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info